Teltonika FM5500 User Manual Download

Page: 17 / 155

3.2

Installing FM5500 drivers

Software requirements

• Operating system 32-bit and 64-bit: Windows XP with SP3 or later, Windows Vista,
Windows 7.
• MS .NET Framework V3.5 or later (

http://www.microsoft.com

Drivers

Please

download

Virtual

COM

Port

drivers

from

Teltonika

website:

http://avl1.teltonika.lt/downloads/FM55/vcpdriver_v1.3.1_setup.zip

Installing drivers

Extract and run VCPDriver_V1.3.1_Setup.exe. This driver is used to detect FM5500 device
connected to the computer. Click 'Next' in driver installation window (figures below):

Figure 4 Driver installation window

This will launch the device driver installation wizard. In the following window click ‘Next’

button again:

Figure 5 Driver installation window

Setup will continue installing drivers and will display a window about successful process in

the end. Click 'Finish' to complete setup:

Summary of Contents for FM5500




























































































































































Search results

Summary of Contents for FM5500

Reviews:

Related manuals for FM5500

Brands by name

Popular brands

Teltonika FM5500, User Manual

Search results

Summary of Contents for FM5500

Reviews:

Related manuals for FM5500

Brands by name

Popular brands