Teltone TLS-4A User Manual Download

Page: 9 / 58

Table 1 Front Panel Switch Functions

Position

Label

Functions

Top

MAN/RING

Momentary contact position with multiple uses:
(1)

Restore defaults:

Within 1 second of turning power

ON, press and hold for 5 seconds to clear all
programming and restore default options. Release after
the POWER light turns ON.

Caution:

Do not use the MA N/RING feature at power

up.

(2)

Manual ring:

With Line 1 on-hook, press and hold to

ring Line 1. Ringing continues until the switch is
released.

(3)

Programming mode:

With Line 1 off-hook, and all

other lines on-hook, press and hold for 1 second to
place the TLS-4A in programming mode.

Center

POWER ON (Press and release the top portion of the
switch.)

Bottom

OFF

POWER OFF

LED Operation

The table below explains how the LEDs on the TLS-4A front panel operate and
what the different blinking patterns indicate.

Table 2 LED Indicators

Indicator

State

Description

Line 1—Line 4

Line is off-hook

Flashing (fast
on/off)

Line is ringing

Blinking (slow
on/off)

Programming mode: Line is
selected for programming

Half brightness

During dialing, indicates that a
valid DTMF digit is present

PWR

Slow blinking

Power is present and processor
is running normally

AUDIO

Audio control lead is on

Reference Manual

Chapter 1: Overview

40-400-00033, Rev.

Page 3

Summary of Contents for TLS-4A



























































Search results

Summary of Contents for TLS-4A

Reviews:

Related manuals for TLS-4A

Brands by name

Popular brands

Teltone TLS-4A, User Manual

Search results

Summary of Contents for TLS-4A

Reviews:

Related manuals for TLS-4A

Brands by name

Popular brands