Teltone TLS-4A User Manual Download Page 47 | Manualshive

Page: 47 / 58

background image

Chapter 7: Warranty, Troubleshooting, and Return

Warranty Information

Teltone warrants this product to be free from defects in material and
workmanship for a period of one year, given proper installation and usage.
At its sole discretion, Teltone will repair or replace free of charge any unit
found to be defective during the warranty period. Units found defective
beyond the warranty period will be repaired or replaced at a flat rate.

Troubleshooting

Before you return a unit, check the fuse.

If the POWER light does not come on when the unit is plugged in and turned
on, try changing the fuse. The active fuse, and a spare, are both located in a
holder on the back panel of the unit, below the power plug, as shown in Figure
6.

1. To remove the fuse holder, insert the blade of a small screwdriver into the
groove at the bottom of the power plug and push outward.

2. The active fuse is the one farthest from the labeled panel; the other fuse is
the spare. Remove the active fuse by pushing on either end.

3. Remove the spare fuse and insert it into the active fuse holder.

Reference Manual

Chapter 7: Warranty, Troubleshooting, and Return

40-400-00033, Rev.

C

Page 41

ACTIVE FUSE

AC POWER

RECEPTACLE

SPARE FUSE

Figure 6 Fuse Holder Location

«
...
45
46
47
48
49
...
»

Summary of Contents for TLS-4A



























































Reviews:

No comments

Related manuals for TLS-4A

Brand: H-TEK Pages: 142

Brand: qua Pages: 2

Blackview GBV7100

Brand: Iget Pages: 62

BLACKBERRY P'9982

Brand: PORSCHE DESIGN Pages: 226

Brand: Blu Pages: 20

Brand: KDDI Pages: 51

Brand: Plum Pages: 21

Brand: Blu Pages: 31

Brand: NGM Pages: 166

Brand: M&T S.A. Pages: 68

Brand: Doogee Pages: 40

Brand: Xiaomi Pages: 50

Brand: Xiaomi Pages: 101

SIP DECT Series

Brand: Teledex Pages: 1

Brand: Zte Pages: 99

Brand: Hi-Tech Pages: 12

Brand: Nokia Pages: 2

Brand: Nokia Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands