Telstra Access 200 User Manual Download Page 53

Page: 53 / 56

5 3

SOME IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment basic safety

precautions should always be followed to reduce

the risk of fire, electric shock and injury to persons,

including the following:

1. Read and understand all instructions.
2. Follow all warnings and instructions marked on

the product.

3. Do not use the Access 200 during an electrical

storm as it is possible to get a shock.

4. Do not use the Access 200 when near water

or when wet.

5. Do not use detergents or sprays on the

Access 200. Clean outside parts with a damp

cloth.

6. Do not open the unit. There are no user

accessible parts inside. Warranty conditions do

not apply if the unit is opened.

7. Keep openings on the Access 200 clear. Keep

away from heaters and out of direct sunlight.

8. Make sure the line cord and AC Power

Adaptor cords are protected from damage. Do

not put the Access 200 where cords can be

damaged by people walking on them.

9. Do not push objects into the openings in the

telephone. This could cause an electric shock.

a200ug.p65

3/7/01, 11:11 AM

Summary of Contents for Access 200

























































Search results

Summary of Contents for Access 200

Reviews:

Brands by name

Popular brands

Telstra Access 200, User Manual

Search results

Summary of Contents for Access 200

Reviews:

Brands by name

Popular brands