telsiu altas START-S3XL Instruction Manual Download Page 7

START-S3XL

Technical Manual

-7-

8    9   10 11  12  13

2.7 

Connection of the STOP/ALT control devices

Connection of the STOP control

Push-button: stops and temporarily prevents all 

control unit function until it is pressed again.

Switch: keeps the automation blocked until it is 

reset.

Connection of the ALT control

Stops the automation and activates an inversion of

direction for approximately 1.5 seconds.

Connection of the safety devices requires the use of any push-button or N.C. (normally closed) contact. 

When there are several safety devices, they are connected in series.

NOLOGO

If the STOP input is 

NOT used put the 

DIP 5 on ON.

If the input 

SAFETY-EDGE

is not used, 

make a link (22-23)

!

2.8 

Connection of LIMIT SWITCHES LSO and LSC

The  fi gure  shows  the  connection  of  both  limit 

switches, however, on this control unit they can also 

be used individually. Therefore, it is possible to use 

just the “Open limit switch” or just the “Close limit 

switch”.

The limit switch contacts must be N.C. 

(normally closed) contacts.

If the LSO or LSC inputs 

aren’t in use, follow the 

instructions you fi nd 

in chapter n. 3

!

2.9 

Connection of the MAGNETIC LIMIT SWITCHES

JUMPER AC/DC

Power Supply

magnetic limit 

switches

+ 24 Vdc

Bring JUMPER 

AC/DC as shown 

in the picture.

22  23

8    9   10 11  12  13 14  15  16 17  18  19

8    9   10 11  12  13 14  15  16 17  18  19

OPEN

N.C.

CLOSE

N.C.

LIMIT

SWITCHES

OPEN

N.C.

CLOSE

N.C.

LIMIT

SWITCHES

Summary of Contents for START-S3XL

















Reviews: