Telos Omnia ONE Multicast Installation And Operation Manual Download Page 56

Page: 56 / 61

Obtaining Service

•

Omnia Customer Support personnel are available in Cleveland, Ohio, USA, Monday through Friday

between 9:00 A.M. and 6:00 P.M., Eastern Time. If outside the U.S.A., please contact the dealer you

purchased your Omnia from.

•

Before contacting Omnia Customer Support, please have the serial number of the unit (located on a barcode

sticker on the rear panel in this format: 0218WXXXX) and a description of the symptoms/problems ready

for the technician.

•

All units being returned to for service MUST have a Return Authorization (RA) number assigned to them

first. Units that are returned without a RA number will experience delays in service.

•

Return the Omnia in its original shipping carton if possible. For best treatment, shipping the Omnia in its

original factory box protects it as well as possible. Damage caused by improper packaging is not covered

under your warranty!

Note: To ensure prompt service, the Return Authorization number must be written
prominently on or near the shipping label on the box!

Via the World Wide Web

The Omnia Web site has a wide variety of information that may be useful for product support, applications
information, software updates, etc. The URL is:

http://www.omniaaudio.com/

Via E-Mail

The customer service e-mail address for Omnia is: [email protected].

Via Phone & Mail (USA and non-European Countries)

Customer service is available by telephone, Monday – Friday between 9:00 A.M. and 6:00 P.M., USA Eastern time

zone.

Phone: +1.216.241.7225 Fax: +1.216. 241.4103

Shipping Information: * Telos / Omnia

2101

Superior

Avenue

Cleveland,

Ohio

44114

USA

ATTN:

the

number

obtained from Omnia Customer Service

Note: To ensure prompt service, the Return Authorization number must be written
prominently on or near the shipping label on the box.

OmniaONE Multicast - Use and Operation Manual – Version 0.90

Summary of Contents for Omnia ONE Multicast






























































Search results

Summary of Contents for Omnia ONE Multicast

Reviews:

Related manuals for Omnia ONE Multicast

Brands by name

Popular brands

Telos Omnia ONE Multicast, Installation And Operation Manual

Search results

Summary of Contents for Omnia ONE Multicast

Reviews:

Related manuals for Omnia ONE Multicast

Brands by name

Popular brands