Telos Omnia ONE Multicast Installation And Operation Manual Download | Manualshive

Page: 14 / 61

background image

CE CONFORMANCE – This device complies with the requirements of the EEC Council
Directives: 93/68/EEC (CE Marking); 73/23/EEC (Safety – low voltage directive); 89/336/EEC
(electromagnetic compatibility). Conformity is declared to those standards: EN50081-1,
EN50082-1.

LITHIUM BATTERY CAUTION – There is a danger of explosion if the internal
battery is replaced incorrectly or shorted. Replace the battery only with same or
equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer's instructions.

USE OF SHIELDED CABLING – In order to conform to the CE requirements for
High Frequency radiation, shielded cables must be used for all audio and data
connections.

NOTE: When the unit is operated in an extremely high RF environment, it may be
helpful to connect cable shields to the XLR-connector terminal that connects cable
shield to chassis ground, not to pin 1. Additionally, a 0.01uF capacitor connected
between XLR pin-1 and the chassis terminal may be helpful in some instances.

RoHS COMPLIANCE –

The RoHS Directive stands for "the restriction of the use of certain

hazardous substances in electrical and electronic equipment". This Directive bans the placing on
the European market of new electrical and electronic equipment containing more than agreed
levels of lead, cadmium, mercury, hexavalent chromium, polybrominated biphenyl (PBB) and
polybrominated diphenyl ether (PBDE) flame retardants.

OmniaONE Multicast is in compliance

with the EU RoHS Directive.

OmniaONE Multicast - Use and Operation Manual – Version 0.90

14

«
...
12
13
14
15
16
...
»

Summary of Contents for Omnia ONE Multicast






























































Reviews:

No comments

Related manuals for Omnia ONE Multicast

Brand: Bosch Pages: 24

Brand: Datavideo Pages: 30

Brand: Epson Pages: 4

Brand: Robot Coupe Pages: 2

Brand: Robot Coupe Pages: 13

Brand: Robot Coupe Pages: 15

Brand: Robot Coupe Pages: 19

Brand: eta Pages: 64

Micro Projector Lift

Brand: Draper Pages: 8

Brand: TECHWOOD Pages: 11

Brand: H.Koenig Pages: 28

Brand: TaoTronics Pages: 15

Brand: XTA Pages: 60

Brand: Vdwall Pages: 112

Brand: TDT Pages: 10

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

HandyChopper HC20

Brand: Black & Decker Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands