tell gsm easyaid Installation And Application Manual Download Page 24

 

24 

3.9  Voice messages, warnings 

 
Some of the events are also indicated by voice messages as follows: 
 

 

Emergency  call  in  progress

”  –  when  the  module’s  emergency  key  or  the  RF 

transmitter’s emergency button is pressed 

 

Emergency  call  cancelled

”  –  when  an  emergency  call  is  cancelled  by  pressing  the 

Cancel key 

 

Calling

” – when speed dialing is initiated using the 1-4 keys 

 

Unsuccessful  call

”  –  if the number called with speed dialing is busy,  unavailable, or 

there is no phone number stored in the given memory section 

 

Settings saved

” – after modifying settings on the module’s user interface 

 

Say the reminder message after the beep

” – when recording a reminder 

 

First reminder

” – when pressing function key 1, if the first reminder’s time is set, but 

no message is recorded 

 

Second  reminder

”  –  when  pressing  function  key  2,  if  the  second  reminder’s  time  is 

set, but no message is recorded 

 

Third reminder

” – when pressing function key 3, if the third reminder’s time is set, but 

no message is recorded 

 

Fourth reminder

” – when pressing function key 4, if the fourth reminder’s time is set, 

but no message is recorded 

 

The battery is low. Please connect the device to the charger

” – if the supply voltage is 

lost  (AC  failure)  and  the  unit’s  battery  has  discharged  below  7.5V.  This  warning 
message is played by 15 minutes until the battery becomes fully discharged and the 
device turn off, or the supply voltage restores.  

Summary of Contents for gsm easyaid




























Reviews: