tell gsm easyaid Installation And Application Manual Download Page 10

 

10 

The  battery  of  the  RF  transmitter  needs  to  be  replaced  forthwith  if 

RF  transmitter 

battery low

” event is received, as well as at least yearly, independently of the reception 

of  this  event,  in  order  to  retain  the  operating  range  of  the  transmitter!  The  user  can 
initiate  emergency  alarms  by  5  seconds  using  the  RF  transmitter,  while  from  the 
easyAID unit this can be done at anytime. 

To cancel or revoke an emergency call press the Cancel 

 key while the countdown 

is shown on the digital display. After an emergency alarm is initiated, the device waits 5 
seconds before initiating the call and sending SMS message, which time is available to 
cancel an alarm initiated by mistake. 
When an  emergency  call  is  initiated,  the  device  calls  the  1-4  phone  numbers  in  order, 
and  then  sends  the  configured  SMS  messages.  If  any  of  the  called  numbers/party 
received and confirmed the call, then the device does not initiate further calls to the next 
phone numbers and does not send any SMS messages about this event. 

ATTENTION! Disable voicemail service on the phone numbers to be dialed by the 
device because in case that the given phone number is not available, this causes 
significant delay to the calls and SMS messages to be initiated to the next phone 
numbers!  The  outgoing  calls  which  are  received  by  voicemail  are  considered 
successful by the device!  

 

Confirming an emergency call 

The called party can confirm the emergency call by pressing 

 

key on the phone. If the 

called party receives the call and presses 

 

key on the phone, the device will not initiate 

further calls to the next phone numbers, considers the emergency call process finished, 
therefore will not send any configured SMS messages about this event. 

2.4.5  Confirming a visit 

The social worker can confirm the visit by entering a 4 digit individual  password (nurse 
code)  consisting  of  digits  1,2,3  and  4,  which  has  to  be  previously  configured  with  the 
programming  software.  If  the  password  has  been  entered  correctly,  the  module 
generates 

Nurse  confirmation

”  event  and  initiates  the  calls  and/or  SMS  sending 

configured for this event. 

Entering the confirmation password: 

1)  Keep the Cancel 

 key pressed for at least 5 seconds 

2)  On digital display 

„- - - -” is displayed 

3)  Enter your 4 digit nurse code using the 1-4 function keys 
4)  If the password has been entered correctly 

ok

” is displayed 

5)  In case of wrong password 

Err

” is displayed 

Summary of Contents for gsm easyaid




























Reviews: