manualshive.com logo in svg

Telereef TR1D, User Manual

Share
Download
Telereef TR1D User Manual Download Page 22

Telereef Controller - User Manual V.140313

!

J.

TxSensor

 - Address of the temperature assign to this position. 

K.

Heater

 - Socket of heater that assign to this Temperature 

Sensor and it’s temperature range. 

L.

Chiller

 - Socket of chiller that assign to this Temperature 

Sensor and it’s temperature range. 

M.

Safety Range

 - Defined safety range of this sensor, if value 

exist this range will activate alert on buzzer and push 
notification.




!

N.

Retry Count

 - No. of retries today to get data from temperature 

sensors. It is an indicator to shows the health of the 
temperature sensors, if something wrong on the sensor or 
interference exists, the retry count may be higher. Retry count 
less than 1000 is normal. 

O.

Edit Button

 - Push this button to setup or modify socket name 

as well as rate/consumption and reference unit. 

P.

S1

 - Socket name for this socket  

Q.

Reference unit

 -  rate / power consumption and unit of this 

socket.




!

R.

Pair Button

 - Push this button to go into Wireless Dosing 

Pump Setting page to discover and pair New Telereef Wireless 
Dosing Pump unit. 

S.

Edit Button

 - Setup chemical name, pump speed and calibrate 

wireless dosing pumps. 

T.

Additive Name

 - The name of additives which connected to the 

pumps. 

U.

Device Address

 - Device address assigned to WDP unit. 

V.

Channel

 - Channel assigned to WDP unit. 

W.

Remain

 - Additives remain in the storage.




!

X.

Reset Button

 - Clear all calibrated pH data, prepare to calibrate again. 

Y.

Edit Button

 - Setup or modify pH Sensor details included raise 

pH socket and pH range, lower pH socket and pH range and 
safety pH range, if value exist this range will activate alert on 
buzzer and push notification. 

Z.

Raise pH range

 - Defined raise pH range 

a.

Lower pH range

 - Defined lower pH range 

b.

Safety range

 - Defined safety range, if value exist this range 

will activate alert on buzzer and push notification. 

c.

pH4 Button

 - Calibrate pH probe in pH4 solution. 

d.

pH7 Button

 - Calibrate pH probe in pH7 solution. 

e.

pH10 Button

 - Calibrate pH probe in pH10 solution. 

f.

Choose File Button

 - Push this button to select a saved 

setting file (setting.ini) to import back to the system. Cannot be 
use on Smart Phone. 

g.

Submit Button

 - Push this button start upload the selected 

22

Summary of Contents for TR1D





























Reviews:

No comments

Brands by name

Popular brands

Load more brands