manualshive.com logo in svg

Telereef TR1D, User Manual

Share
Download
Telereef TR1D User Manual Download Page 13

Telereef Controller - User Manual V.140313

!

• Wireless Dosing Pumps

!




Telereef Wireless Dosing Pump WDP need to be paired before use. Please follow the 
procedures below to pair the WDP unit. 

!

1. Login to Web Interface and go to Setup page. 
2. Scroll down to Wireless Dosing Pump Section, push 

Pair button 

3. Input a four characters password, wireless address 

value 1-200 and a wireless channel value 1-99. 
Each WDP unit occupied 2 wireless addresses and 
1 wireless channel for send and receive data. 
System will issue address and channel to new 
paired WDP unit starting from the value you input. 
Eg. if address 121 and channel 76 is input, first WDP will be assigned address 
121/122 and channel 76, second WDP will be assigned 123/124 and channel 77, 
third WDP will be assigned 125/126 and channel 78.  

4. Make sure you have saved the above settings before go to next step. 
5. Put only 

ONE

 WDP device in Pair Mode (See instruction on WDP manual) 

6. Reload Wireless Dosing Pump settings page. 
7. If WDP Device is in range and found, message "Found unpaired Telereef WDP" will 

display together with the Device ID and Firmware Version. 

8. Push “Pair” button on which address you want to assign and then push OK. 
9. If the WDP successfully paired, message “Congratulation! WDP paired” will display 

and the Device ID and Firmware Version of WDP will display on same row of the 
paired address. You will also hear two short beep from the WDP. The LED indicator 
on WDP Device will flash every 5 seconds if within signal range. 

10.If WDP Device cannot be found, move the WDP Device closer to the Telereef 

Controller and try again. 

!

!

• Alert and Push notification (Prowl / Notify)

!

!

Telereef Controller provides two kinds of alert method, they are 
internal beep sound and push notification to Smart Phone. Under 
the following conditions Telereef Controller will issue an alert to one 
or both methods. 

!

!

• System Restart (Push Notification only) 

(Priority: Very low)

!

• Temperature Sensors reading out of range. 

(Priority: Very high)

 

!

• Temperature Sensors not responding. 

(Priority: Very high)

!

• pH Sensor out of range. 

(Priority: Normal)

!

• Wireless Dosing Pump additive out of stock. 

(Priority: Low)

!

• Wireless Dosing Pump not responding. 

(Priority: Low)

!

!

Same condition will only alert once within 15 minutes or until the 
condition has been fixed. 

!

!

There is a buzzer inside Telereef Controller generates beep sound if any above 
conditions has occurred, the beep sound can be changed by adjusting the length of beep 
and interval between beeps in System Settings page, if the beep is too loud, you may set 

13

Telereef Wireless Dosing Pump

Summary of Contents for TR1D





























Reviews:

No comments

Brands by name

Popular brands

Load more brands