Teledyne T3PS16081P User Manual Download

Page: 9 / 65

User Manual 2

EAR99 technology subject to restrictions on copyrights page.

1.1 General Inspection

Please inspect your new instrument, follow the steps below.

1. Inspect the shipping container

Keep the shipping container or cushioning material until the contents of the

shipment have been completely checked and the instrument has passed both

electrical and mechanical tests. The consigner or carrier is responsible

for damages to the instrument resulting from shipment.

Teledyne LeCroy

will not provide free maintenance or replacement for shipping damages.

2. Inspect the instrument

If there is damage, defects, or failures in electrical and mechanical tests of the

product, please contact your nearest

Teledyne LeCroy

sales representative.

3. Check the accessories

Please check the accessories according to the packing list. If the accessories

are incomplete or damaged, please contact your

Teledyne LeCroy

sales

representative.

Summary of Contents for T3PS16081P


































































Search results

Summary of Contents for T3PS16081P

Reviews:

Related manuals for T3PS16081P

Brands by name

Popular brands

Teledyne T3PS16081P, User Manual

Search results

Summary of Contents for T3PS16081P

Reviews:

Related manuals for T3PS16081P

Brands by name

Popular brands