Teledyne T3PS16081P User Manual Download

Page: 49 / 65

User Manual 42

EAR99 technology subject to restrictions on copyrights page.

Return Info

10.11.13.214

、

MASKaddr

Command format

MASKaddr <NetMask>

Description

Used to assign a subnet mask to the instrument

Example

Explanation

MASKaddr 255.255.255.0

This command is invalid when the power is currently set

to automatically obtain the network configuration (DHCP

is ON)

Command format

MASKaddr?

Description

Query the software the setting of the mask address

Example

SYSTem: VERSion?

Return Info

255.255.255.0

、

GATEaddr

Command format

GATEaddr <GateWay>

Description

Used to assign agateway to the instrument

Example

Explanation

GATEaddr 10.11.13.1

This command is invalid when the power is currently set

to automatically obtain the network configuration (DHCP

is ON)

Summary of Contents for T3PS16081P


































































Search results

Summary of Contents for T3PS16081P

Reviews:

Related manuals for T3PS16081P

Brands by name

Popular brands

Teledyne T3PS16081P, User Manual

Search results

Summary of Contents for T3PS16081P

Reviews:

Related manuals for T3PS16081P

Brands by name

Popular brands