Telecrane F21-12D Manual Download Page 5

Page: 5 / 31

TCM260904

Rev

0.1

TCM260904

Page 5 of 31

GENERAL CHARACTERISTIC

ENERAL

PECIFICATIONS

- Operating Frequency--------------------- : 415 ~ 483 MHz (set by software)

- Hamming Distance ----------------------- :

≧

- I.D. Code----------------------------------- : 232; more than 4 billion sets (set by factory, never repeated)

- Temperature Range----------------------- : -35

℃

~ +75

℃

- Channel Spacing-------------------------- : 5KC/6.25KC or integral multiple (set by software)

- Maximum Operating Range------------ : Up to 100 Meters

- Structure----------------------------------- : Fibre-Nylon

- Protection Degree------------------------ : IP 65

RANSMITTER

PECIFICATIONS

- Power Supply----------------------------- : Four 1.5volt Alkaline or Rechargeable Batteries (AA Size)

- RF Power---------------------------------- :

10 mW

- Modulation-------------------------------- :

≤

2.5KHz; NBFM

- Pushbutton Type-------------------------- : Two step Mechanical Switch

- Dimensions-------------------------------- : 186x61x51mm (excluding protrusion)

- Weight------------------------------------- : about 360g (including batteries)

ECEIVER

PECIFICATIONS

- Power Supply----------------------------- : AC 110/220/380V (50/60Hz) (tolerance±10%)

- Sensitivity---------------------------------- :

−

110DBm (Date Error Rate

−

- Image Rejection--------------------------- : > 60dB

- Rejection of Adjacent Channels ------- : > 80dB (± 20KC)

- Output Relays----------------------------- : 10A/250VAC; 8A/30VDC

- Dimensions-------------------------------- : 200x162x107mm (excluding protrusion)

- Weight------------------------------------- : about 1640g (excluding wire cable)

Summary of Contents for F21-12D
































Search results

Summary of Contents for F21-12D

Reviews:

Related manuals for F21-12D

Brands by name

Popular brands

Telecrane F21-12D, Manual

Search results

Summary of Contents for F21-12D

Reviews:

Related manuals for F21-12D

Brands by name

Popular brands