Tektronix TLA 714 Service Manual Download Page 74

Page: 74 / 159

Removal and Installation Procedures

TLA 714 Color Portable Mainframe Service Manual

4–27

Disconnect

Remove
screws (4)

Fan tray

Cord-wrap feet

Figure 4–12: Rear chassis fan tray removal

Use the following procedure to reinstall the rear chassis fan tray:

1. Redress the cable connecting the rear chassis fan tray to the backplane board

if necessary.

2. Reconnect the cable connecting the rear chassis fan tray to the backplane

board.

3. Reposition the rear chassis fan tray.

4. Reposition the cord-wrap feet (they snap into holes on the rear chassis fan

tray), and insert the four screws that secure the rear chassis fan tray to the
mainframe.

Installation

Summary of Contents for TLA 714
































































































































































Search results

Summary of Contents for TLA 714

Reviews:

Related manuals for TLA 714

Brands by name

Popular brands

Tektronix TLA 714, Service Manual

Search results

Summary of Contents for TLA 714

Reviews:

Related manuals for TLA 714

Brands by name

Popular brands