manualshive.com logo in svg

Tektronix TLA 714, Service Manual

Share
Download
Tektronix TLA 714 Service Manual Download Page 68

Removal and Installation Procedures

TLA 714 Color Portable Mainframe Service Manual

4–21

Right side cover

Left side

cover

Screws (4)

Top cover

Screws (2)

Figure 4–9: Top and side cover removal

Left Side Cover

No screws attach the left side cover to the mainframe. However, you must loosen
the two screws closest to the left side of the bottom cover in order to remove the
left side cover.

You will need a screwdriver with a size T-15 Torx

 

tip to perform this procedure.

Use the following procedure to remove the left side cover:

1. Do the Trim Ring removal procedure, steps 1-5, on page 4–10.

2. Do the Top Cover removal procedure on page 4–20.

3. Loosen the two screws on the bottom cover closest to the left side of the

mainframe. (See Figure 4–6 on page 4–11.)

4. Remove the left side cover.

Removal

Summary of Contents for TLA 714
































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands