manualshive.com logo in svg

Tektronix TLA 714, Service Manual

Share
Download
Tektronix TLA 714 Service Manual Download Page 60

Removal and Installation Procedures

TLA 714 Color Portable Mainframe Service Manual

4–13

Remove screws (5)

Display
backlight
cable

Flat panel display

assembly

Disconnect

the cable

Figure 4–7: Flat panel display assembly removal

Use the following procedure to reinstall the flat panel display assembly:

1. Reattach the cable connecting the flat panel display assembly to the interface

board.

2. Reattach the display backlight cable.

3. Reinstall the flat panel display assembly by first inserting the top edge and

then rotating it downward into position. (Be sure the tabs are engaged at the
top of the assembly. Insert the five screws that attach the flat panel display
assembly to the mainframe: two screws at the bottom of the assembly on the
front of the instrument, two screws on the top, and one screw on the left side.
(See Figure 4–7 on page 4–13).

4. Do the Trim Ring installation on page 4–11.

Installation

Summary of Contents for TLA 714
































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands