background image

Specifications

Version 00b

MTS400 Series Performance Verification and Specifications Technical Reference

1−11

Table 1

8 lists the electrical characteristics for the COFDM measurements.

Table 1−8: COFDM measurements 

Characteristic

Description

Overall receiver lock status

Overall receiver lock status is indicated by an LED on
the rear panel

Transmission coding parameters

The receiver reports the current status of the
following transmission parameters:
− QPSK/16, QAM/64, QAM encoding
− 2K/8K Transmission mode
− Hierarchy status (hierarchy on/off, alpha value) 
− Viterbi puncture rate
− Guard Interval Value
− Gross bit rate in the channel
− Spectrum polarity (inverted/non-inverted)

Input level (signal strength)

Ranges, High Sensitivity mode: 
QPSK (4QAM): −85 dBm to −10 dBm  (24 dBuV to
99 dBuV)
16QAM: −80 dBm to −10 dBm  (29 dBuV to
99 dBuV)
64QAM: −72 dBm to −13 dBm  (37 dBuV to
96 dBuV)

Ranges, High Resolution mode: 
QPSK (4QAM): −45 dBm to −10 dBm  (64 dBuV to
99 dBuV)
16QAM: −45 dBm to −10 dBm  (64 dBuV to
99 dBuV)
64QAM: −45 dBm to −13 dBm  (64 dBuV to
96 dBuV)

Resolution: 1 dBm
Accuracy: 

"

3 dBm

RF carrier offset

Accuracy: 

"

50 ppm of the tuned frequency

SNR (Signal to Noise Ratio)

Display Range:
6 dB to 40 dB for QPSK (4QAM) 
11 dB to 40 dB for 16QAM 
16 dB to 40 dB for 64QAM

Resolution: 1 dB

Accuracy: 

"

1 dB to 30 dB SNR (measured at

−30 dBm input in high resolution mode)

COFDM Card

Measurements

Summary of Contents for MTS415

















































Reviews: