Tekron TCG 01-G Page 9 User Manual Download | Manualshive

Page: 9 / 52

background image

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 9

www.tekron.com

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

When the TCG 01-G is synchronized to a source other than GNSS, this field directly indicates the
alternate sync source being used by the TCG 01-G. Table 2 shows the alternate sync sources
supported by the TCG 01-G.

Character

Values

Description

Satellites in
the sky

“0 - 9”: 0 - 9
“A - E”: 10-14
“F”: > 14

This character represents the total number of satellites
currently present in the sky according to the GNSS almanac.
“0” in this position means that TCG 01-G has lost its

knowledge of the GNSS satellites’ orbit geometries. This
occurs if the unit has been in storage for an extended period,
or if the GNSS receiver has been reset.
It will typically take 20 minutes (worst case two hours) for the
unit to gain sufficient GNSS synchronization for the TCG 01-G
to recommence normal operation (Position hold).

Satellites
tracked

“0 - 9”: 0 - 9
“A - E”: 10-14
“F”: > 14

This digit represents the number of satellites currently being
used to compute the time solution.
A “0” value means that no updated time solution is available
(“out of lock” condition).
If this condition persists for the “Holdover” time the clock will
indicate the “out of sync” condition.

Receiver
status

“A”

TCG 01-G is in Acquiring mode - attempting to get satellite
fixes.

“G”

“Poor satellite geometry”: Satellites are positioned in almost a
straight line, so the best accuracy cannot be obtained, but the
unit will still sync to UTC.

“S”

A Site Survey is in progress. The TCG 01-G is calculating an
accurate position. Once complete, the mode will change to

Position hold.

“P”

“Position hold”: The position is known accurately, and the

GNSS reference is providing its most accurate time, typically
better than 40 ns to UTC.

Satellites in sky

Satellites tracked

Receiver status

LST: TUE 17MAR10

076 11:16:53 87A

LST: TUE 17MAR10

076 11:16:53 SL1

«
...
7
8
9
10
11
...
»

Summary of Contents for TCG 01-G





















































Reviews:

No comments

Related manuals for TCG 01-G

Brand: Danfoss Pages: 7

Brand: Danfoss Pages: 16

VLT 2800 Series

Brand: Danfoss Pages: 34

VLT AutomationDrive FC 300

Brand: Danfoss Pages: 60

VLT 5000 Series

Brand: Danfoss Pages: 63

Brand: Baldor Pages: 146

Brand: Orban Pages: 90

AURORA PVI-3.0-OUTD-S-US

Brand: Power One Pages: 108

Brand: Vacon Pages: 12

Brand: HIKVISION Pages: 50

Brand: Oriental motor Pages: 56

Brand: Kramer Pages: 17

Brand: Daihen Pages: 158

Brand: FBS Pages: 6

Brand: KONANlabs Pages: 6

Brand: SICK Pages: 21

Brand: GoMax Electronics Pages: 12

Brand: Optelecom-nkf Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands