manualshive.com logo in svg

Tekron TCG 01-G, User Manual

Share
Download
Tekron TCG 01-G User Manual Download Page 19

TEK-TCG 01-G-Manual-v6-052021 

P a g e

 | 19 

www.tekron.com 

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The 

information in this document is provided for informational use only and is subject to change. For further information or support, 
go to www.tekron.com.

 

P6: Event Recording / IRIG-B Sync Inputs (4-pin 3.81 mm Connector) 

The pluggable connector provides two input channels that may be driven by 
TTL sources. The input can be either be configured for a pulse for event 
recording or for receiving un-modulated IRIG-B – IRIG-B004 with C37.118.1 
extensions only. This option allows IRIG-B to be used as a secondary sync 

source.  

The input type is software configurable. If both event recording and IRIG-B sync input functions 
are selected, then channel ‘A’ is the Event Input and channel ‘B’ is the IRIG-B sync input. 
The expected input is 5 V, 7 mA, however inputs up to 10 V, 20 mA may be applied. The ‘+’ and 
‘-’ symbols represent the positive and negative terminals respectively. The supported wiring 
size is up to 1.00 mm². 
The two ports are isolated from the rest of the system by a 2.5 kV barrier and the ports have a 
60 VDC isolation from each other. Each input is protectively clamped to 25 V and uses a 470 Ω 

resistor to limit the current. 
Refer to the Event Recording Specification section of this manual for further information on the 
event recording feature. 
 

P7: Sync Relay (4-pin 3.81 mm Connector) 

P7

 provides two alarm output channels. 

P7 A

 is the GNSS signal receive fail (Antenna fail) alarm. The antenna alarm 

only occurs after a continuous 5 seconds with the antenna disconnected or 
short-circuited. 

P7 B

 is a synchronization fail alarm. This alarm is active (contact open) when 

the unit is not synchronized and is not in the holdover state. 
The alarm outputs are Type A (

normally-open

) dry contact types (implemented using solid state 

relays).  

Note

: the “

Normally-Open

” descriptor refers to the de-energized state of the relay. 

The TCG 01-G operates with the alarm relays energized during normal operation, and de-

energized in the alarm state. In the case of all power to the clock being lost, all of the alarm 
relays will default to the “alarm” state (open contact).  
The “+” and “-” symbols are included for reference purposes only, as the alarm contacts are not 
polarized. The supported wiring size is up to 1.00 mm², and the contact rating is 200 V, 150 mA 
DC or 150 V, 100 mA AC. 
 

Summary of Contents for TCG 01-G





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands