Tekron TCG 01-G Page 4 User Manual Download

Page: 4 / 52

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 4

www.tekron.com

information in this document is provided for informational use only and is subject to change. For further information or support,
go to www.tekron.com.

String-F Time Code O/P on P4 ............................................................................................... 41

String-G Time Code O/P on P4............................................................................................... 42

String-H Time Code O/P on P4 ............................................................................................... 44

NMEA ZDA Time Code O/P on P4 .......................................................................................... 45

NMEA RMC Time Code O/P on P4 ......................................................................................... 46

IRIG-B Specification ............................................................................................................... 47

Event Recording Specification ................................................................................................................ 48

Tag Data ................................................................................................................................. 48

Tag Storage ............................................................................................................................ 48

Tag Retrieval .......................................................................................................................... 48

TCG 01-G Command / Response Message structure ............................................................ 48

TCG 01-G Commands related to Event Time Tagging ........................................................... 49

Ps command: Get Status........................................................................................................ 49

Notes concerning the Ps command:

...................................................................................... 50

Pc command: Clear Time-Tag Buffer ..................................................................................... 50

Pt command: Get next Time-Tag ........................................................................................... 50

Pr command: Repeat last Tag Sent ........................................................................................ 51

10.

WARRANTY......................................................................................................................... 52

Summary of Contents for TCG 01-G




















































Search results

Summary of Contents for TCG 01-G

Reviews:

Related manuals for TCG 01-G

Brands by name

Popular brands

Tekron TCG 01-G, User Manual

Search results

Summary of Contents for TCG 01-G

Reviews:

Related manuals for TCG 01-G

Brands by name

Popular brands