Tekron TCG 01-G Page 12 User Manual Download | Manualshive

Page: 12 / 52

background image

TEK-TCG 01-G-Manual-v6-052021

P a g e

| 12

www.tekron.com

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,
go to www.tekron.com.

Alarm Messages

When an alarm condition is active, a four-character message is shown on the top line of the
LCD, replacing the normal date information (see example in Figure 8 above). The possible alarm
messages are shown below:

LCD Alarm Alarm Name Description

Hold

Holdover

The TCG 01-G is operating in the “holdover” state (Holdover timer running).

Sync

No Sync

The TCG 01-G is not synchronized to any source and holdover period has expired.

AntL

No Antenna The antenna circuit current drain is low (typically under 3mA). This could be

caused by poor connections, or if the connected antenna has a lower current
drain specification or if a component in the antenna system is providing power to
the antenna and therefore the clock is not seeing a connected load.

AntH

Antenna
Short

The antenna circuit current drain is high (typically over 100 mA). This is caused by
a short in the antenna circuit, or by moisture ingress in the circuit, or if the
antenna connected has a higher current draw specification.

IRIG

No IRIG-B
Input

IRIG-B monitoring is enabled on the P6A and/or P6B input, and a valid IRIG-B
signal is not present on that input.

IPe1

IPv4 Address
Fault on

ETH1

The clock has failed to obtain an IPv4 address via DHCP, or has detected an IP
address conflict, and has adopted an ARP tested Link-Local address

(169.254.xxx.xxx).
When this alarm occurs, the user may need to update their network adapter

settings to a Link-Local address to gain access to the clock.
The alarm will persist until the IPv4 address settings are changed or the clock is
connected to a DHCP enabled network.

FRP Armed
Press Again

to Disarm

Factory
Reset

Procedure
(FRP) Armed

This message appears on the LCD, in place of all other text, when the Factory
Reset Procedure is initiated by the user. The Factory Reset Procedure is used to

reset the TCG 02-G to factory default settings in the case of a lost or forgotten
administrator password, or configuration error that renders the TCG 02-G
inaccessible. Refer to the Tekron Configuration Tool Manual for further
information.

Table 5 – Alarm Messages

«
...
10
11
12
13
14
...
»

Summary of Contents for TCG 01-G





















































Reviews:

No comments

Related manuals for TCG 01-G

Brand: Tascam Pages: 35

Brand: Briggs & Stratton Pages: 60

Brand: Transition Networks Pages: 13

Auto-Link-SPE-G

Brand: I-novative Pages: 10

Brand: Suaoki Pages: 32

Brand: ADF Web Pages: 25

Brand: Kramer Pages: 30

ServeMaster 1600MV

Brand: IBC SOLAR Pages: 58

Brand: Airpax Dimensions Pages: 6

Brand: Black Box Pages: 20

Y/C to NTSC Conversion PCN-40

Brand: Link Pages: 2

Brand: Wirez Pages: 16

Brand: wagner solar Pages: 52

Brand: Cross Technologies Pages: 24

Brand: Delta Electronics Pages: 181

Grass Valley LUMO

Brand: Belden Pages: 71

Brand: ADF Web Pages: 24

Brand: red lion Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands