manualshive.com logo in svg

Tekron TCG 01-G, User Manual

Share
Download
Tekron TCG 01-G User Manual Download Page 47

TEK-TCG 01-G-Manual-v6-052021 

P a g e

 | 47 

www.tekron.com 

© 2021 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The 

information in this document is provided for informational use only and is subject to change. For further information or support, 

go to www.tekron.com.

 

IRIG-B Specification 

 

Figure 13 – Image sourced from IRIG Standard 200-04 

Only the IRIG ‘B’ format is supported by Tekron products, but all three modulations are 
supported. With DCLS/no modulation (pulse width code) no carrier is used, and with 
Manchester modified and amplitude modulation (AM) only the 1khz carrier is supported. 
Therefore Tekron products support IRIG-B00x, IRIG-B12x, and IRIG-B22x where ‘x’ is the coded 

expression.  
For the coded expression, BCDtoy and BCDyear are always included in the signal, but straight 

binary seconds (SBS) are only included if ‘binary seconds in code’ is enabled, and the control 
field (CF) is only included if either AFNOR or C37.118.1 extensions are used. Therefore, coded 
expressions 4-7 are supported by Tekron products. Tekron recommends using coded expression 
4 with C37.118.1 extensions, as this provides the most information possible to end devices. 

Summary of Contents for TCG 01-G





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands