Tekron NTS 03-G+ User Manual Download Page 3

Page: 3 / 32

TEK-NTS03-G+-Manual-v3.-012022

P a g e

| 3

www.tekron.com

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

Location ................................................................................................................................................... 23

Hazardous Voltage .................................................................................................................................. 23

Earthing ................................................................................................................................................... 24

Mounting the NTS 03-G+ ........................................................................................................................ 24

Operation ................................................................................................................................................ 24

FACTORY RESET ..................................................................................................................... 25

FACTORY HARDWARE OPTIONS ............................................................................................ 26

Power Supply Options ............................................................................................................................. 26

Expansion Board Options ........................................................................................................................ 26

Slave Only Option (Fiber input) ............................................................................................................... 26

OCXO Option ........................................................................................................................................... 26

Rubidium Option ..................................................................................................................................... 27

APPENDIX ............................................................................................................................... 28

NTS 03-G+ Specifications ........................................................................................................................ 28

Physical Specifications ........................................................................................................... 28

GNSS Receiver ........................................................................................................................ 28

Input & Output Connector Specifications ............................................................................. 28

Input & Output Specifications ............................................................................................... 29

DC-IRIG/AM-IRIG Availability ................................................................................................. 29

IRIG-B Translation Chart ........................................................................................................ 30

Environmental Specifications ................................................................................................ 31

Electrical Specifications ......................................................................................................... 31

10.

WARRANTY ............................................................................................................................ 32

Notes ....................................................................................................................................................... 32

Summary of Contents for NTS 03-G+
































Search results

Summary of Contents for NTS 03-G+

Reviews:

Related manuals for NTS 03-G+

Brands by name

Popular brands

Tekron NTS 03-G+, User Manual

Search results

Summary of Contents for NTS 03-G+

Reviews:

Related manuals for NTS 03-G+

Brands by name

Popular brands