Tekron NTS 03-G+ User Manual Download Page 22 | Manualshive

Page: 22 / 32

background image

TEK-NTS03-G+-Manual-v3.-012022

P a g e

| 22

www.tekron.com

© 2022 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

5.

SOFTWARE

Configuration Tool

The NTS 03-G+ can be configured via USB or Ethernet. The configuration tool can be downloaded

from the Tekron Support Website:

www.support.tekon.com.

By default, the unit is shipped with

DHCP enabled for automatic IP address assignment, with a fall back to link local addressing

(169.254.xxx.xxx) if no DHCP server is present.

Default Username:

admin

Default Password:

Password

Note:

The user is required to change the default password on first login.

USB driver

The USB driver can be downloaded from the NTS 03-G+ product page of the Tekron website

https://tekron.com/products/multiport-network-time-server-nts03g

).

«
...
20
21
22
23
24
...
»

Summary of Contents for NTS 03-G+

































Reviews:

No comments

Related manuals for NTS 03-G+

LS42 - BladeCenter - 7902

Brand: IBM Pages: 194

Brand: Patton electronics Pages: 331

Brand: 360 Systems Pages: 117

Brand: Datacom Pages: 89

Brand: Vitek Pages: 2

Brand: Vxl Pages: 2

Brand: Avaya Pages: 119

Brand: Portwell Pages: 21

Brand: PRG Pages: 50

Brand: PRG Pages: 136

ProLiant ML350 Gen10

Brand: Hewlett Packard Enterprise Pages: 214

Brand: Oce Pages: 464

NET-SERV Series

Brand: Panduit Pages: 24

Brand: ICP DAS USA Pages: 26

Xtreme PC NG6450

Brand: Chip PC Pages: 4

Brand: Black Box Pages: 46

Brand: BushkaBlue Pages: 30

Brand: Advantech Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands