Tekron NTS 03-G+ User Manual Download

Page: 32 / 32

TEK-NTS03-G+-Manual-v3.-012022

P a g e

| 32

www.tekron.com

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

10.

WARRANTY

For terms and conditions of Tekron’s Warranty see the Web Site

http://tekron.com/about-tekron/warranty

WARNING:
This product has been designed to comply with the limits for a Class A digital device pursuant to

Part 15 of FCC rules. These limits are designed to provide reasonable protection against such

interference when operating in a commercial environment.

Notes

The information in this manual may change without notice. The manufacturer assumes no

responsibility for any errors that may appear in this manual.

Ethernet is a trademark of XEROX Corporation. Windows, Windows 95, Windows 98, Windows

2000, Windows NT, Windows XP, Windows Vista, and Windows 7 are trademarks of Microsoft™

Corp.

Copyright ©2022 Tekron International Ltd. All rights reserved. No part of the contents of this

document may be transmitted or reproduced in any form or by any means without the written

permission of Tekron International Ltd. Published in New Zealand.

This product has been manufactured by Tekron in New Zealand. For more information on

Tekron or its products please visit our website at

www.tekron.com

Summary of Contents for NTS 03-G+
































Search results

Summary of Contents for NTS 03-G+

Reviews:

Related manuals for NTS 03-G+

Brands by name

Popular brands

Tekron NTS 03-G+, User Manual

Search results

Summary of Contents for NTS 03-G+

Reviews:

Related manuals for NTS 03-G+

Brands by name

Popular brands