Tekron NTS 03-G+ User Manual Download Page 5 | Manualshive

Page: 5 / 32

background image

TEK-NTS03-G+-Manual-v3.-012022

P a g e

| 5

www.tekron.com

© 2022 by Tekron International Limited. All Rights Reserved. All trademarks are the property of their respective holders. The

information in this document is provided for informational use only and is subject to change. For further information or support,

go to www.tekron.com.

Configuration

The NTS 03-G+ features an administrative 10/100 Mbps Ethernet port through which the unit’s

inputs and outputs can be configured. When the IEEE 1588-2008 (PTPv2) option is enabled, the

unit can operate as a PTP grandmaster, an ordinary PTP clock, or a slave only clock.

Accessories

The NTS 03-G+ comes complete with Ethernet cables to allow for customization and easy setup

from the Windows™ Configuration software which is available to download from

www.support.tekron.com.

Optional accessories include antenna, low loss antenna cable, antenna pipe mounting

components, lightning protection kit, in-line amplifiers, and connector adaptors.

«
...
3
4
5
6
7
...
»

Summary of Contents for NTS 03-G+

































Reviews:

No comments

Related manuals for NTS 03-G+

Express 5800 Series

Brand: NEC Pages: 90

PDS-220F Series

Brand: ICP DAS USA Pages: 94

Express5800/T110g-S

Brand: NEC Pages: 34

eserver pSeries 690

Brand: IBM Pages: 142

eServer 370 xSeries

Brand: IBM Pages: 218

BladeCenter PS703

Brand: IBM Pages: 298

BladeCenter T Type 8720

Brand: IBM Pages: 180

Brand: SEH Pages: 20

Brand: I-O DATA Pages: 49

Brand: Sercomm Pages: 75

SuperWorkstation 740A-T

Brand: Supermicro Pages: 138

Brand: W&T Pages: 228

SUPERSERVER 5019S-M

Brand: Supermicro Pages: 65

Brand: DNP Pages: 93

Brand: Intel Pages: 32

BladeCenter PS703

Brand: IBM Pages: 198

Brand: Kraun Pages: 36

1870N - HL B/W Laser Printer

Brand: Brother Pages: 204

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands