Tekno RC NB48.4 Building Instructions Download

Page: 15 / 32

TKR1403

TKRBB050825

Note: Apply

a small drop

of oil for

easy o-ring

installation.

Note: Tighten nut all the way down,

then back it off 3 full turns

Stock Position

(is MIDDLE hole)

(front of vehicle)

TKR8100

TKR5056

TKR5123

TKR8052A

TKR8104

TKR5101X

TKR5231

TKR1201

TKRBB06103

TKR1529

Note: Stock bumpsteer setting is 4

washers over the steering ball link.

4 x TKR1221

TKR1221

TKRBB06103

TKRBB050825

TKR8104

TKR5122

TKR8100

TKR1529

TKR5122

TKR1221

TKR1201

TKR5103

TKR1403

TKRBB06103

TKR5123

TKR8052A

26.50

TKR1201

M3 Lock Nut Black

O-ring 16x12x2

TKR5231

TKRBB06103

Ball Bearing (6x10x3)

TKRBB050825

Ball Bearing (5x8x2.5)

TKR1529

M3x20mm Cap Head Screw

TKR1221

M3x8mm Washer

TKR8052A

Thread

Lock

Thread

Lock

Thread

Lock

Left/Right x 2pcs

Step

K-1

Step

K-2

Step

K-3

Step

K-4

TKR8052A

Pivot Ball M3x6.8mm

TKR1403

M3x10mm Button Head Screw

Actual Size

Bag K

Steering Assembly
(overview)

Note: Notch always goes

on left side of vehicle

Summary of Contents for NB48.4

































Search results

Summary of Contents for NB48.4

Reviews:

Related manuals for NB48.4

Brands by name

Popular brands

Tekno RC NB48.4, Building Instructions

Search results

Summary of Contents for NB48.4

Reviews:

Related manuals for NB48.4

Brands by name

Popular brands