Tek Drive TDS-F8, Instruction Manual

Page: 62 / 74

60
4-05
Multi-
function Input
MI2 Selection
00- REV of 3 wires CTL 14- PID disable
01- Run Command by OP 15- PID (I) Reset
02- Run Command by TMN 16- OH pre-alarm
03- Fault Reset
17- External Fault (N.O.)
04- Multi-step SPD 1 18- External Fault (N.C.)
05- Multi-step SPD 2 19 & 20- Reserved
06- Multi-step SPD 3 21- SPD Search from 1-03
07- JOG Frequency REF 22- SPD Search from FRQ REF
08- ACC/ DEC Time1/ 2
switching
23- TIMER Function Input
24- MOP UP/ DN ( only for 4-
08
，
then MI4-UP/ MI5-DN)
09- ACC/ DEC disable
10- B.B. Input (N.O.)
25- Count present value clear
11- B.B. Input (N.C.) 26- Counter Input
12- FWD JOG (FJOG) Run 27~ 31- Reserved
13- REV JOG (RJOG) Run
*: The setting value of Multi-function Digital Inputs must
meet the rule of MI2< MI3< MI4< MI5.
3
4-06
Multi-
function Input
MI3 Selection
4
4-07
Multi-
function Input
MI4 Selection
5
4-08
Multi-
function Input
MI5 Selection
6
4-09
Control Terminal Signal Scan Time
0- Scan 1 Time (5ms)
1- Scan 2 Times (10ms)
1
4-10
Analog Input Filter Constant 1~ 80 10
4-11
Counter Target Value 0~ 9999 0
5- Multi-preset Reference & Auto Process Operation Parameters
No. Parameter Name & Description Setting Range Default User set
5-01 Preset Reference 1
0.0~ 400.0Hz
0.0Hz(
☆
)
5-02 Preset Reference 2
0.0~ 400.0Hz
0.0Hz(
☆
)
5-03 Preset Reference 3
0.0~ 400.0Hz
0.0Hz(
☆
)
5-04 Preset Reference 4
0.0~ 400.0Hz
0.0Hz(
☆
)
5-05 Preset Reference 5
0.0~ 400.0Hz
0.0Hz(
☆
)
5-06 Preset Reference 6
0.0~ 400.0Hz
0.0Hz(
☆
)
5-07 Preset Reference 7
0.0~ 400.0Hz
0.0Hz(
☆
)
5-08 Preset Reference 8
0.0~ 400.0Hz
0.0Hz(
☆
)
5-09
Auto Process Operation Mode Selection:
0- Auto Process is disabled.
1- Executes 1 Cycle operation then stop.
2- Continuously Executes Cycles Operation.
3- Executes 1 Cycle operation then Keep running at last Preset REF.
4- Executes 1 Cycle operation then stop.
5- Continuously Executes Cycles Operation.
6- Executes 1 Cycle operation then Keep running at last Preset REF.
*5-09= 1~ 3, if the run command is given again after F8 stopped, the F8
will start to run from the Frequency Reference before last stop.
5-09= 4~ 6, if the run command is given again after F8 stopped, the F8
will start to run from the Preset Reference 1.
0
5-10 Process Operating Mode Selection 1
0- STOP
1- FWD
2- REV
0
5-11 Process Operating Mode Selection 2 0
5-12 Process Operating Mode Selection 3 0