3
Disarming diagnostics
If the Alarm was triggered in Security mode, then you will hear four
audible signals when disarming despite of whether silent arming mode
is on or off. Triggered zones will be indicated by LED prior to first igni
-
tion activation (see Trigger diagnostics table)�
Table 2� Trigger diagnostics
Quantity of LED light signals
Reason (zone) of Alarm triggering
2
Hood
3
Trunk
4
Doors
5
Sensor 1 Alarm
6
Sensor 2 Alarm
7
Sensor 1 Warning
8
Sensor 2 Warning
9
Protection of public order
Alarm triggering
In the Security mode, the Alarm can react to actions with your vehicle
in two ways: Warning and Alarm� The Warning triggers when there
are weak effects on the shock sensor, e�g� due to vibrations caused by
passing transport� In this case the siren emits several short signals�
Alarm signal is activated if any of the doors, hood or trunk were opened
and when there was a strong effect on shock sensor� Siren will be on for
30 seconds and hazard lights will blink�
Protection of public order function
If the alarm has been triggered three times in one hour via the
shock sensor, the Alarm will stop responding to the sensor� The Alarm
will continue responding to the sensor only after the effects on the
sensor will not repeat within an hour or if the Alarm was disarmed and
rearmed� This function is not part of Warning mode�
Arming with sensors inputs deactivation
If one of kit sensors is installed:
◊
Arm the vehicle
◊
Rearm the vehicle within 3 seconds� The siren will emit one long
and one short signal: the Warning input will be deactivated�
◊
Within the next 3 seconds rearm the vehicle� The shock sensor
will be completely deactivated
If other sensors are installed:
◊
Arm the vehicle�
◊
Rearm the vehicle within 3 seconds� The siren will emit one
long and one short signal: Sensor input No� 1 will be deacti-
vated (if silent arming mode is on, the siren will emit only one
short signal)�
◊
Next arming (within 3 seconds) will deactivate both sensor in-
puts: sensor input No� 1 and sensor input No� 2� The siren will
emit one long and two short signals (if silent arming mode is
on, the siren will emit only two short signals)�
Automatic windows closing when arming
Several seconds (1 to 3 depending on vehicle model) after arming,
the Alarm activates the Comfort feature of the vehicle� Sensors out-
puts are ignored for all the time of sensor inputs operation�
Trunk opening without leaving the Security mode
When opening the trunk with remote control in Security mode ac-
cessory external sensors’ inputs are temporarily deactivated (sensor
input No� 1 and sensor input No� 2 – see Alarm inputs/outputs sec-
tion)�
Central locking control
The Alarm has automatic central locking activation when driving be-
gins (when vehicle speed exceeds 5 km/h) and central locking deactiva-
tion when the key is removed from ignition� If the vehicle has analogi-
cal original functions, it is strongly recommended to use them and keep
the corresponding Alarm functions deactivated�
PIN and PUK codes
PIN code
PIN code is a secret combination of original vehicle button(s) press-
ings. Please see the Integrator files for the list of original buttons
perceived by the Immobilizer� PIN code needs to be entered prior to
driving the vehicle�
PIN code is a one-, two-, three- or four-digit number� Each digit is
a figure from 1 to 9.
PIN code can be promptly changed numerous times by both techni-
cal specialists during Immobilizer installation or by you during day-
to-day vehicle use�
Factory default settings
PIN code – 2 is entered with the Programming button – see In-
tegrator files. Upon Alarm installation the factory-set PIN code
is to be changed for the purposes of providing the proper se-
crecy level� If the PIN code is not changed, a beep tone will be
activated after factory-set PIN code entering in order to remind
the necessity of PIN code changing�
PUK code
In case if the vehicle owner loses the PIN code, the Alarm supports
the entering of the PUK code�
PUK code completely replaces the PIN code but cannot be changed
during operation�
PUK code is located under the protective layer on the plastic card�
PUK code entering is carried out by Programming button with 2-sec-
ond pause after each digit� PUK code can be entered with the in-
tegrated Programming button and with the original vehicle button
assigned as the Programming button�
Only the vehicle owner must know the PUK code�
Upon successful PUK code entering a new PIN code can be pro-
grammed�
PIN code entering
PIN code is entered with vehicle ignition on by steadily pressing
the original vehicle’s buttons� When entering one of the PIN digits,
please make sure that pressure or pause duration is no longer than
1 second�
Please keep the pause of approximately 2 seconds in between the
digits� If you made a mistake while entering the PIN code, please wait
for longer than 3 seconds and re-enter the PIN code�
PIN code entering sequence
◊
Turn the ignition on (the LED will turn on)�
◊
Enter the PIN code�
◊
Wait for audible confirmation trill (the LED will turn off)
