12
Programming examples
Example 1
Objective:
You would like to change the factory settings of the Alarm:
set output No� 2 Engine locking to control the normally open relay�
Execution:
◊
Turn the ignition on�
◊
Enter the PIN code and wait for confirmation�
◊
Enter Menu 1 by pressing and releasing the Programming
button 10 times� If you have performed all the actions cor-
rectly, the Alarm will notify you of it with 3 audible and
light signals�
◊
According to Alarm hardware functions configuring
(Menu 1) option No� 2 Engine locking is to be selected� To
do so, press and release the Programming button 2 times�
The Alarm will inform you on the selected menu option
number by series of 2 audible and light signals�
◊
Enter option No� 2 by pressing and holding the brake pedal�
The Alarm will inform you on the option setting by repeated
double audible and light signals because the current (fac-
tory set) option setting is normally closed relay control�
◊
Select the normally open relay control by pressing and re-
leasing the Programming button 3 times, for the second
setting is followed by the third� The Alarm will inform you
on the option setting with series of 1 audible signal�
◊
Exit programming mode by turning the ignition off�
Example 2
Objective:
You would like to change the factory settings of the Alarm:
to increase the Anti HiJack activation distance from 100 to 300 meters�
Execution:
◊
Turn the ignition on�
◊
Enter the PIN code and wait for confirmation�
◊
Enter the Alarm setting mode by pressing and releasing
the Programming button 12 times (start doing it no longer
than 10 seconds after entering the PIN code)� If you have
performed all the actions correctly, the Alarm will notify
you of it with 4 audible and light signals�
◊
Select the programming option for setting the Anti HiJack
activation distance� According to Alarm user settings con-
figuration (Menu 2) table, option No� 5 is to be selected� To
do so, press and release the Programming button 5 times�
The Alarm will inform you on the selected menu option
number by series of 5 audible and light signals�
◊
Enter option No� 5 by pressing and holding the brake pedal�
The Alarm will inform you on the option setting by repeated
single audible and light signals because the current (fac-
tory set) option setting is 1 (which stands for 100 meters
distance)�
◊
Change option No� 5 setting by pressing and releasing the
Programming button twice, therefore increasing the option
setting by 2 (1+2=3)� The Alarm will inform you on the op-
tion setting with series of 3 audible and light signals (300
meters)�
◊
Exit the setting mode by turning the ignition off�
Resetting to factory default settings
The Alarm has a procedure of resetting the programmable settings,
where all vehicle model settings are removed from Alarm’s permanent
memory while PIN code and all other programming options are re-
turned to factory original val-
ues�
If certain or all menu op-
tions are password protected
(see Alarm hardware settings
programming (Menu 1), p�
2), only the options that are
not prohibited will be reset�
The remaining ones will keep
their current values�
In order to reset to factory default:
1
Remove power supply from the Alarm
2
Press and hold the integrated Programming button (see Fig� 2)
3
Connect the power supply while holding the button� The Alarm
will emit dashed audible signal�
4
Release the button and wait until the dashed signal stops�
5
Turn the ignition on and enter the current PIN code
*
�
6
An audible trill will be heard, which indicates that resetting to
factory default has been completed�
7
Remove the power supply and disconnect the Alarm from CAN
bus�
*
If the Alarm is not installed in the vehicle, please enter the PUK code with
the integrated button�
Fig� 2� Integrated button
