manualshive.com logo in svg

TDK-Lambda GXE600 Series, Communications Manual

Share
Download
TDK-Lambda GXE600 Series Communications Manual Download Page 36

COMMUNICATION MANUAL

GXE600 SERIES

TDK­Lambda

<Page>

36/79

#

1

Re gist e r  Nam e

Remote On/Off

Data Type

Register Function

Starting Address

Qty

Non-volatile

Holding

Remote On/Off (Volatile)

1

No

Holding

Remote On/Off (Non-Volatile)

1

Yes

1) Register Details

This register manipulates the remote control signal via communication.

It is possible to remotely control the output of the GXE by writing the reference value to the register.

Prior to operation, it is necessary to set "Remote On/Off configuration register" to enable setting of remote control signal

via communication. There are two remote ON / OFF registers, but only the registers set with

"Remote On/Off configuration register" are referenced.

・Register setting value

Value

Function

0

Remote Off 

1

Remote On

* If an unspecified value is written, only the lowest bit is accepted as a valid value.

・Remote on / off registers have volatile and nonvolatile registers.

Register

Description

Remote On/Off

GXE will start from the default value each time AC input.

(Volatile)

Because the register value is "Volatile".

Remote On/Off

GXE follows the previously set remote on / off signal.

(Non-Volatile)

Because the register value is "Non-Volatile".

These registers behave differently when brownout occurs for a certain time or more. 

The figure below shows the operation image.

The Remote On / Off (Volatile) signal starts from "Remote Off" state even after brownout occurs.

On the other hand, Remote On / Off signal (Non-Volatile) maintains the "Remote On" state even after brownout occurs.

*

 Whether " Remote On/Off ( Volatile ) " volatilizes or not depends on the degree of brownout.

- Caution -

The remote control signal is not referred for depending on the setting of "Remote On/Off configuration register".

However, Register value can be changed regardless of whether or not the "Remote On / Off register" is referred.

GXE performs the output operation based on the current register value.

In some cases, output of GXE may be started just by changing the "Remote On/Off configuration register".

Factory setting

AC input

0 ： Remote Off

-

(Previously set)

0 ： Remote Off

(0x0000)

(0x0001)

0

(0x0000)

5

(0x0005)

Summary of Contents for GXE600 Series
















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands