TC Electronic SYSTEM 6000 MKII Algorithm Manual Download Page 81

Page: 81 / 124

DE-EssEr

Introduction

DeEssing is a well-known dynamics tool made for removing

unwanted sibilant sounds. This version in System 6000 is

improved significantly - e.g. with 48bit internal processing -

enabling the process to be performed from 100Hz to 20kHz

giving the option to also use it as e.g. a de-popper.

A unique feature allowing the Threshold to operate either

Relatively to average level of the signal or Absolute to

0dBFS, makes the DeEsser work extremely musical e.g. on

vocals that have a constant flaw regardless of the level.

The DeEsser is operating in Stereo, Dual-mono or M/S

processing modes.

Threshold

When the input level exceeds the Threshold, the DeEsser

will be in operation.

Threshold performance depends on the ‘Threshold

Mode’ setting (Relative or Absolute) on the setup

page.

Ratio

The Ratio of the gain reduction. When the Ratio is set

to 4:1 it means that for every 4dB the defined frequency

range rises, the output level increases by only 1dB.

Attack

The Attack time is the response time that the DeEsser

uses to reach the gain reduction specified by the Ratio

parameter.

Release

Release sets the fall-back time of the DeEsser, after the

signal drops below the Threshold.

Frequency

Sets the center frequency of the range the DeEsser will

operate in.

Curve

Sets the bandwidth or Lo/Hi shelf setting of the range the

DeEsser will work in.

Side Chain

Pressing

Sidechain

enables to monitor the part of

the signal that is defined by the Frequency and Curve

parameters. This is the part of the signal that the DeEsser

will “compress” when in operation. Adjusting the Frequency

and Curve parameters when monitoring the sidechain,

makes it a lot easier to hear where the sibilant problems

occur in the signal.

Inlevel Left and Right

Range: Off to +12dB

Adjusts the Input level for the two channels.

Outlevel Left and Right

Range: Off to +12dB

Adjusts the Output level for the two channels.

Phase Invert Left and Right

Applies Phase inversion of the respective Input channel.

Threshold Mode

Decides how the Threshold shall react. When set to

Relative, the Threshold will be relative to the average

level of the signal. This means that also soft signals

are processed. For signals where the average level is

determined by signals outside the frequency range set,

for example, a vocal with sibilance, the Relative setting is

useful and very musical. When Mode is set to Absolute,

the Threshold set refers to full scale, 0dBFS, and is

therefore well suited for limiting the maximum level in a

specified frequency range, e.g. the bass.

The De-Ess algorithm occupies:

@ Normal Sample Rate : 1/4 DSP Resource

@ Double Sample Rate : 1/4 DSP Resource

Algorithm Inputs/Outputs are distributed as follows:

E1 - E4

L
R
Thru
Thru
Thru
Thru
Thru
Thru

Thru
Thru
Thru
Thru
Thru
Thru

INPUT

OUTPUT

•

Summary of Contents for SYSTEM 6000 MKII





























































































































Search results

Summary of Contents for SYSTEM 6000 MKII

Reviews:

Related manuals for SYSTEM 6000 MKII

Brands by name

Popular brands

TC Electronic SYSTEM 6000 MKII, Algorithm Manual

Search results

Summary of Contents for SYSTEM 6000 MKII

Reviews:

Related manuals for SYSTEM 6000 MKII

Brands by name

Popular brands