background image

RouterBOARD 1000

User's Manual

Copyright and Warranty Information

Copyright   and   Trademarks

.   Copyright   MikroTikls   SIA.  This   manual   contains   information   protected   by 

copyright law. No part of it may be reproduced or transmitted in any form without prior written permission  
from the copyright holder. RouterBOARD, RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls 
SIA. All trademarks and registered trademarks appearing in this manual are the property of their respective 
holders.

Hardware

. MikroTikls SIA warrants all  RouterBOARD series equipment  for the term of one year from the 

shipping date to be free of defects in materials and workmanship under normal use and service, except in 
case   of   damage   caused   by   mechanical,   electrical   or   other   accidental   or   intended   damages   caused   by  
improper use or due to wind, rain, fire or other acts of nature.

If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding  
all   warranty   and   repair   issues,   the   following   instructions   apply  

ONLY

  if   you   purchased   your   equipment 

directly from MikroTik Latvia

To   return   failed   unit   or   units   to   MikroTikls   you   must   perform   the   following   RMA   (Return   Material 
Authorization) procedure. Follow the instructions below to save time, efforts, avoid costs, and improve the  
speed of the RMA process. Take into account that all goods have one year warranty. 

Instructions are located on our webpage here: 

http://rma.mikrotik.com

Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but 
not limited to, the implied warranty of merchantability and fitness for a particular purpose. The 
manufacturer has made every effort to ensure the accuracy of the contents of this manual, however, it is 
possible that it may contain technical inaccuracies, typographical or other errors. No liability is assumed for 
any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or other 
damages that may result from such an inaccuracy, including, but not limited to, loss of data or profits. 
Please report any inaccuracies found to [email protected]

Summary of Contents for RouterBOARD 1000










Reviews: