Taylor-Dunn RE-380-36 Service And Replacement Parts Manual Download

Page: 56 / 150

Transaxle - SD

Page 56

RE-380-36 & RE-380-48

MR-380-05

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

3RD MEMBER

Illustration is for reference only. This assembly is not serviceable with the exception

of oil seals.

HARDWARE TORQUE

If hardware is not listed here, refer to standard torque

values in the appendix.

Description

Foot Pounds Newton Meters

Pinion nut

275-300

392-428

Drain plugs

9-14

13-20

Fill plugs

45-50

64-71

Gear case to 3rd member

45-55

64-78

Primary housing bolts

23-27

33-38

3rd Member cover bolts

45-55

64-78

Ring Gear

70-80

100-114

Axle hub bolt

275

392

Summary of Contents for RE-380-36























































































































































Search results

Summary of Contents for RE-380-36

Reviews:

Related manuals for RE-380-36

Brands by name

Popular brands

Taylor-Dunn RE-380-36, Service And Replacement Parts Manual

Search results

Summary of Contents for RE-380-36

Reviews:

Related manuals for RE-380-36

Brands by name

Popular brands