Taylor-Dunn RE-380-36 Service And Replacement Parts Manual Download

Page: 141 / 150

Replacement Parts

Page 141

* Not available at time of printing

MR-380-05

RE-380-36 & RE-380-48

MIRRORS

Mirrors

Item No. Part No.

Description

Qty

92-201-00

Mirror, rectangular, 4-1/2 x 8-1/2 (side view)

92-202-12

Mounting bracket, left, Steel cab

92-202-13

Mounting bracket, right, Steel Cab

91-814-16

Hinge, left (used with 92-202-12)

91-814-17

Hinge, right (used with 92-202-13

92-202-15

Spacer (used with 92-202-12 and -13)

92-207-00

Mirror, multi-panel (inside cab)

91-810-00

Mounting tab for multi-panel mirror

97-176-00

Washer, Neoprene

92-206-00

Mirror, rectangular, 5-1/2 x 8 (inside cab)

02-210-70

Bracket for 92-206-00

Summary of Contents for RE-380-36























































































































































Search results

Summary of Contents for RE-380-36

Reviews:

Related manuals for RE-380-36

Brands by name

Popular brands

Taylor-Dunn RE-380-36, Service And Replacement Parts Manual

Search results

Summary of Contents for RE-380-36

Reviews:

Related manuals for RE-380-36

Brands by name

Popular brands