manualshive.com logo in svg

Taylor-Dunn RE-380-36, Service And Replacement Parts Manual, Page: 23 / 150

Share
Download
Taylor-Dunn RE-380-36 Service And Replacement Parts Manual Download Page 23

Tool List

Page  23

MR-380-05

RE-380-36 & RE-380-48

77-201-00: Battery Filler
Used to safely add water to batteries. 

Equipped with splash guard and auto-

shutoff when cell is full.

70-440-55: Pin Removing Tool
Removes pin from Amp circular harness 

connectors.

Molex # 11-300-06: Pin Removing Tool
Removes 0.093 diameter pins from Molex 

rectangular harness connectors. Not 

available from Taylor-Dunn. Purchase from 

any local electronics distributor.

75-442-55: Pin Removing Tool
Removes pins from Molex Mini-Fit harness 

connectors.

77-200-00: Hydrometer
Used for testing battery electrolyte. 

Illustration is of a typical hydrometer, actual 

hydrometer type may vary.

Molex # 11-300-02: Pin Removing Tool
Removes 0.062 diameter pins from Molex 

rectangular harness connectors. Not 

available from Taylor-Dunn. Purchase from 

any local electronics distributor.

Summary of Contents for RE-380-36























































































































































Reviews:

No comments