manualshive.com logo in svg

Taylor-Dunn B 2-48, Operation, T Roubleshooting And Replacement Parts Manual

The Taylor-Dunn B 2-48 Operation, Troubleshooting, and Replacement Parts Manual is a comprehensive guide for users of this versatile electric vehicle. This essential manual covers everything from operation instructions to troubleshooting tips and is available for free download on our website. Get your copy and unleash the full potential of your Taylor-Dunn B 2-48!

Share
Download
background image

Electrical Troubleshooting

Charger Troubleshooting 

  Page 8

TROUBLESHOOTING FOR PORTABLE CHARGER

Disconnect the charger from the AC outlet and the batteries.

1. Test the voltage from the positive terminal on the vehicles DC receptacle to main

battery negative. This voltage should be equal to the battery voltage. If the voltage
is less than the battery voltage then this wire is broken or has a bad connection.

Stop here and repair the problem.

2. Test the voltage from the positive terminal on the DC receptacle to the negative

terminal on the DC receptacle. This voltage should be equal to the battery voltage.
If the voltage is less than the battery voltage, then the wire on the negative terminal
of the DC receptacle is broken or has a bad connection.  

Stop here and repair the

problem.

Remove the charger cover and perform the following tests:

1. Inspect the internal wiring of the charger and repair as required.
2. Check the continuity of both fuse links and replace if bad.
3. Disconnect one lead from the capacitor. Test the capacitor using the capacitor

test function on the meter. If the capacitor is bad, it must be replaced. 

Stop here

and repair the problem.

4. Reconnect the lead to the capacitor and

disconnect one transformer lead from one of
the diodes. Test each of the diodes using the
diode test function on the meter. If either one of
the diodes are bad, replace the diode
assembly.  

Stop here and repair the problem.

Fuse Links

Capacitor Test

HIGH VOLTAGE may be stored in the capacitor. Discharge the capacitor

before continuing. Connect a 2k ohm resistor across the capacitor

terminals for 10 seconds. Do not touch the capacitor terminals with

your hands.  The resistor should be held with a pair of insulated pliers.

Failure to do so may cause serious bodily injury

Summary of Contents for B 2-48









































































































































































































































Reviews:

No comments

Related manuals for B 2-48

Dongfang Motor DF150GKA Assembly Instructions Manual preview
DF150GKA
Brand: Dongfang Motor Pages: 28
Strongway 51962 Owner'S Manual preview
51962
Brand: Strongway Pages: 15
Variant PRO-LINE User Manual preview
PRO-LINE
Brand: Variant Pages: 16
Turbosol T20X Use And Maintenance Manual preview
T20X
Brand: Turbosol Pages: 84
Fayat Group BOMAG BW 213 D-5 Operating Instruction, Maintenance Instruction preview
BOMAG BW 213 D-5
Brand: Fayat Group Pages: 222
Yamaha YFM7RD Owner'S Manual preview
YFM7RD
Brand: Yamaha Pages: 162
Yamaha YFM 90 2021 Owner'S Manual preview
YFM 90 2021
Brand: Yamaha Pages: 126
Can-Am 2008 DS 450 Operator'S Manual preview
2008 DS 450
Brand: Can-Am Pages: 148
ODES 1000ATV-L Owner'S Manual preview
1000ATV-L
Brand: ODES Pages: 89
Marlon MAR ATV 1605 Owner'S Manual preview
MAR ATV 1605
Brand: Marlon Pages: 9
Razor DIRT QUAD 500 Owner'S Manual preview
DIRT QUAD 500
Brand: Razor Pages: 16

Brands by name

Popular brands

Load more brands