English
Steam Station
SLIDING PRO 3000 NON STOP
DESCRIPTION
1.Water tank
2.Water tank cap
3.Locker button
4.Lampshade
5.Steam adjustment button
6.Calc cleaning button (Selfcleaning)
7.Continuous steam button
8.Soleplate
9.Clamp for cord storage
a.Calc cleaning indicator
b.No water warning
c. MAX steam
d. Auto shut off indicator
e.Eco mode with lower steam
SUGGESTIONS BEFORE USING THE IRON
FOR THE FIRST TIME
-Certain parts of the iron have been lightly
greased therefore the iron could give off a little
smoke when plugged in for the first time. This
will cease after a short while.
-Before using the iron for the first time , remove
the plastic protector from the base (if it has
one) clean the base with a soft cloth.
-Keep the base very smooth. Do not run it over
metal objects (such as against the ironing
board, buttons , zips ,etc.)
-Pure wool fibres (100% wool)can be ironed
with the appliance in the steam position .by
preference ,select a high steam position and
use a dry ironing cloth.
STEADY TEMPERATURE
-Check the ironing instructions on the garment
to be ironed.
-Electronic temperature control, no need to
manually adjust temperature
HOW TO FILL THE WATER TANK.
-Disconnect iron power supply
-Open the water cap
-Fill the water tank to the MAX water level and
close the cap. Fig.1
-If you have hard water ,it is advisable to use
only distilled or demineralized water.
-Do not use chemically delimed water or perfu-
med
STEAM IRONING
-Fill the iron as described in the section “how to
fill the water tank”.
- Plug the iron into the mains.
-Steam ironing is possible only when heating
is complete.Otherwise ,water may escape
through the soleplate.
-Wait until the indicator does not flicker to prove
that the bottom plate has been heated.
-Press Steam switch to realize Steam ironing.
Fig. 2
-When the iron is finished, place the iron in an
upright position or on the base when the iron is
interrupted
-Disconnect the iron from the mains supply.Pour
of any remaining water and leave the iron to
cool off.
CONTINUOUS STEAM
-Heating completed, temperature stabilized
-Start steam switch, can choose large steam or
ECO steam at the same time, the two stalls can
be switched at any time. Fig. 3
SHOT OF STEAM
-When the heating is completed, the temperatu-
re is stable.
-Press the steam in two seconds quickly, and
the steam will start to explode in two seconds,
while the steam will flash for 2 seconds. Fig.4
SELF CLEANING
-Please make sure there is enough water in the
tank before cleaning
-Please put the iron in a safe position before
cleaning to prevent people from being injured
by hot water during cleaning
-After the heating is complete , the long press
the cleaning switch for 3 seconds , and the iron
enters the cleaning mode .The display on the
screen flashes and goes with the 3 sound of
bees. Fig. 5
-Two minutes later, the buzzer rang three times,
indicating that the cleaning was complete.
Summary of Contents for Sliding Pro 3000 Non Stop
