manualshive.com logo in svg

TAU STERIL FAST B, User Manual

Share
Download
TAU STERIL FAST B User Manual Download Page 22

    

TAU STERIL

 

 

 

N° 11 - Rev. 3  03/02/20 

 

 

 

 

User Manual 

Page 22 

FAST B

 

4.8    Alarm messages and signals  

Throughout the sterilisation cycle, the machine displays messages on the touch-screen. These inform the

 

operator of 

the correct operation of the

 

appliance or any fault or error occurring during the sterilisation cycle (alarm).

  

 

The table below lists the alarms and respective messages programmed in the machine:

 

 

No.  Message displayed 

Description 

Solution 

1 

FILL TANK 

Tank fill level low

 

 

Top up demineralised water, section 3

 

 

2 

FILL TANK TO BE EMP-

TIED 

Tank full  

Empty used water tank, section 3.2

 

 

3 

MISSING LINE LOCK 

No Sync signal (50 Hz)

 

 

Repeat the cycle. If the problem persists, contact tech-

nical assistance.

 

 

4 

FILLER TANK SENSOR 

DEFECTIVE 

 Filler tank sensor 

Contact  technical assistance 

5 

TRIAC Q8 OPEN 

SUPPLY SHUT OFF 

Electronic component 

Turn the machine off and on again. If the problem per-

sists, contact technical assistance.

 

 

6 

TRIAC Q9 OPEN 

SUPPLY SHUT OFF 

Electronic component 

Turn the machine off and on again. If the problem per-

sists, contact technical assistance.

 

 

7 

TRIAC Q10 OPEN 

SUPPLY SHUT OFF 

Electronic component 

Turn the machine off and on again. If the problem per-

sists, contact technical assistance.

 

 

8 

PRESSURE WRONG IN 

THE PHASE PR 

Alarm low temperature in phase PR

 

 

Allow the machine to cool. Inspect and clean the door 

seal (maintenance section  5). Repeat the cycle. If the 

problem persists, contact technical assistance.

 

 

9 

WRONG TEMPERATURE IN 

THE PHASE PR 

Alarm, high temperature in phase PR

 

 

Allow the machine to cool. Inspect and clean the door 

seal (maintenance section 5). Repeat the cycle. If the 

problem persists, contact technical assistance.

 

 

10 

PHASE NOT COMPLETED 

Vacuum phase not executed

 

 

Dirt on door seal:  

Inspect and clean the door seal (maintenance section 5). 

Repeat the cycle. If the problem persists, contact tech-

nical assistance.

  

 

11 

TANK TEMP. HIGH COO-

LING PHASE 

Chamber heating element temperature 

high: cooling pause

 

 

The sterilisation chambre temperature is high: wait for 

cooling with door open 

12 

TRIAC Q15 OPEN 

SHUT OFF 

Electronic component 

Turn the machine off and on again. If the problem per-

sist, contact technical assistance.

 

 

Summary of Contents for FAST B







































Reviews:

No comments

Brands by name

Popular brands

Load more brands