TASKalfa 3011i Page 497 Operation Manual Download | Manualshive

Page: 497 / 610

background image

10-16

Troubleshooting > Troubleshooting

Troubleshooting

Solving Malfunctions

The table below provides general guidelines for problem solving.

If a problem occurs with your machine, look into the checkpoints and perform procedures indicated on the following
pages. If the problem persists, contact your Service Representative.

Machine Operation Trouble

When the following machine operation troubles occur, implement appropriate procedures.

NOTE

When contacting us, the serial number will be necessary.
To check the serial number, refer to the following:

Display for Device Information (page 2-18)

Symptom

Checkpoints

Corrective Actions

Reference

Page

An application does not
start.

Is the Auto Panel Reset time short?

Set the Auto Panel Reset time to 30
seconds or more.

The screen does not
respond when the power
switch is turned on.

Check the power cord.

Connect both ends of the power
cord securely.

―

Is the machine powered on?

Turn on the main power switch.

Pressing the [

Start

] key

does not produce copies.

Is there a message on the screen?

Determine the appropriate response
to the message and respond
accordingly.

Blank sheets are ejected. Are the originals loaded correctly?

When placing originals on the
platen, place them face-down and
align them with the original size
indicator plates.

When placing originals in the
document processor, place them
face-up.

―

Check that the settings of the
application software.

―

Paper often jams.

Is the paper loaded correctly?

Load the paper correctly.

―

Turn the orientation 180 degrees
around in which the paper is
positioned.

Is the paper of the supported type?
Is it in good condition?

Remove the paper, turn it over, and
reload it.

Is the paper curled, folded or
wrinkled?

Replace the paper with new paper.

Are there any loose scraps or
jammed paper in the machine?

Remove any jammed paper.

«
...
495
496
497
498
499
...
»

Summary of Contents for 3011i



































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 3011i

Brand: Raymarine Pages: 135

WorkCentre Pro 90

Brand: Xerox Pages: 36

8437477 - EasyShare ESP 9 All-In-One Printer

Brand: Kodak Pages: 143

Brand: idp Pages: 88

Brand: Savin Pages: 4

Brand: AstroJet Pages: 32

Brand: Intermec Pages: 282

Brand: Parkside Pages: 77

ECOSYS M3860idn

Brand: Kyocera Pages: 483

Brand: Ricoh Pages: 849

imagePRESS V1000

Brand: Canon Pages: 123

Brand: Epson Pages: 277

Brand: Epson Pages: 288

Brand: Epson Pages: 283

Brand: Epson Pages: 60

TRST-A10 SERIES

Brand: Toshiba Pages: 6

Brand: Toshiba Pages: 13

Brand: Toshiba Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands