Task Force Tips MONSOON MONITOR Instructions For Installation, Safe Operation And Maintenance Download Page 11 | Manualshive

Page: 11 / 44

background image

11

4.2 INLET FITTING OR EXTEND-A-GUN RC INSTALLATION

The Monsoon Monitor is available with various inlet fittings as shown in fig 3.3A. When the inlet fittings are used see figure 4.2A for the
addition to overall height. The Monsoon Monitor also connects directly to TFT's Extend-A-Gun RC3 or RC4. The fittings and Extend-A-
Gun RC are attached to the monitor by means of a threaded joint with an o-ring seal. Once in the proper orientation the threaded joint is
locked from rotation by two ¼-28 button head cap screws as shown in figure 4.2B. This makes for easy removal of the monitor since the
large threads of the joint are not tightened and do not have any thread locking compounds on them. It is best to install the inlet fitting or
Extend-A-Gun RC to the apparatus and than install the monitor to the inlet

or Extend-A-Gun RC. This gives more room to install

the bolts in the case of flanged

s. Referring to figures 4.2B and 4.2C the installation sequence is as follows:

1) Install inlet

or Extend-A-Gun RC to apparatus.

•

Mount so that 180 degree apart threaded crossholes will give desired direction relative to the “Straight Ahead Reference Mark”

when the monitor is installed. See figure 4.2B.

2) Screw monitor onto inlet

or Extend-A-Gun RC until threaded joint bottoms out.

•

Do not use pipe dope or Loctite on the inlet base threads. These threads are sealed with an o-ring. The use of thread locking

compounds will make removal difficult.

3) Unscrew monitor slightly until a pair of 90 degree apart slots lines up with the 180 degree apart threaded crossholes in the inlet

or Extend-A-Gun RC.

•

Orient monitor so that the Straight Ahead Reference Mark is facing the desired direction.

•

Slots will line up with threaded crossholes every 90 degrees of rotation.

•

Monitor may be unscrewed up to one full turn from the bottomed out position.

4) Install ¼-28 by ½ long button head cap screws and washers in the two threaded crossholes. Use Loctite #271 on the threads of the

button head cap screws.

fitting

fitting

fitting

fitting

fitting

Allow Loctite to fully cure before applying water pressure.

MODEL

INLET FITTING

ADDITIONAL

TYPE

HEIGHT

Y4-*1*A

3" ANSI 125/150

0.75"

DN8, PN20

20mm

Y4-*2*A

4" ANSI 150

0.94"

DN100, PN20

24mm

Y4-*4*A

DN80, PN16

0.75"

20mm

Y4-*5*A

DN100,PN16

0.94"

24mm

Y4-*6*A

3" NPT FEMALE

2.00"

51mm

Y4-*7*A

4" NPT FEMALE

1.75"

45mm

Y4-*8*A

3" BSP MALE

2.30"

58mm

Y4-*9*A

4"BSP MALE

2.30"

Fig 4.2A Additional Height for Inlet Fittings

Fig 4.2B Inlet Fitting Connection

«
...
9
10
11
12
13
...
»

Summary of Contents for MONSOON MONITOR













































Reviews:

No comments

Related manuals for MONSOON MONITOR

Brand: Pall Pages: 51

Brand: ZAMST Pages: 21

Brand: Kapriol Pages: 32

Brand: Xo Pages: 59

Brand: Falcon Pages: 8

Brand: Gamry Instruments Pages: 69

Brand: Gamry Instruments Pages: 30

Brand: Gamry Instruments Pages: 88

Brand: Rayger Pages: 2

Brand: SAMCHULLY Pages: 48

Brand: HAGER WERKEN Pages: 2

Brand: Tanaka Pages: 20

Brand: Tandem Pages: 80

Brand: Tanco Pages: 4

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

TITAN 2967-033A

Brand: Yetter Pages: 20

Brand: Kanlux Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands