Task Force Tips MONSOON MONITOR Instructions For Installation, Safe Operation And Maintenance Download Page 14 | Manualshive

Page: 14 / 44

background image

4.5 ELEVATION TRAVEL STOPS

The range of elevation travel for the Monsoon Monitor is 90 degrees above zero to 45 degrees below zero. The elevation range may be
limited by installing the supplied stop bolts at the locations shown is figures 4.5A and 4.5B. Consult factory for other ranges. The figures
include installation notes.

Fig 4.5A

Elevation Travel Limits

Fig 4.5B

Elevation Travel Stop Locations

Pry out plastic plug and install Stop Bolt
to obtain desired travel limits.

Elevation travel with no Stop Bolts is
90° above and 45° below zero.

4.6 PRESSURE GAGE PORT

There is a ¼” NPT female threaded hole on the back of the monitor. The hole is plugged from the factory. If a pressure gage is desired,
unscrew the plug and install the gage using pipe sealant. Make sure the gage does not interfere with the elevation handwheel.

4.7 DRAIN

There is no drain on the Monsoon Monitor itself. A drain valve should be installed on the monitor's inlet piping.

14

PLASTIC
PLUG
#VM4124

A

30° ABOVE

HORIZONTAL

B

45° ABOVE
HORIZONTAL

STOP BOLT
#Y4145

C

30° BELOW
HORIZONTAL

«
...
12
13
14
15
16
...
»

Summary of Contents for MONSOON MONITOR













































Reviews:

No comments

Related manuals for MONSOON MONITOR

Brand: MacDon Pages: 2

Brand: MacDon Pages: 214

Brand: MacDon Pages: 32

Brand: Fisher Scientific Pages: 42

Brand: T-Rex Pages: 13

Brand: DBX Bushido Pages: 12

Brand: Ecler Pages: 108

Brand: R&S Pages: 121

Brand: Federal Signal Corporation Pages: 4

Brand: ParaBody Pages: 7

Brand: Garmin Pages: 2

Brand: Halyard Pages: 88

Brand: HALDER Pages: 2

Brand: Hällde Pages: 40

Brand: Hällde Pages: 6

Brand: Pari Pages: 50

Brand: Icare Pages: 42

Brand: tayco Pages: 111

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands