Tao Motor BULL 200s Owner'S Manual Download Page 56

Page: 56 / 79

The engine oil level should be checked before each ride. In addition, always follow the maintenance schedule for oil changes as shown in

the maintenance schedule.

Place the ATV on a level surface.

Check the engine oil level

when

engine

is cold

Remove the engine oil filler cap

(dipstick)

wipe off

dipstick

with a clean rag.

Slowly thread the dipstick back in the filler hole, then remove it again to check the oil level.

If the engine oil is at or below the minimum level mark, add sufficient oil of the recommended type to raise it to the correct level.

NOTICE: Be sure the engine oil is at the correct level, otherwise engine damage may result.

Check the 0-ring for damage, and replace it if necessary

on dipstick

Insert the dipstick into the oil filler hole

and tighten.

1. Minimum Oil Level Mark

2. Maximum Oil Level Mark

TIP

To check the engine oil level

NOTE

Your new vehicles engine comes with shipping oil, shipping oil must be changed before the engine is

started for the first time. Please see specification chart for recommended oil type.

If the engine was started before checking the oil level, be sure to warm up the engine sufficiently, and

then wait at least ten minutes until the oil settles for an accurate reading.

The engine oil dip stick is located on the right side of the ATV behind the right foot rest.

TIP

Only add engine oil into the dipstick

filler

hole

. Never

pour

engine oil

anywhere else other than dipstick filler

hole.

ENGINE OIL

Summary of Contents for BULL 200s
















































































Search results

Summary of Contents for BULL 200s

Reviews:

Related manuals for BULL 200s

Brands by name

Popular brands

Tao Motor BULL 200s, Owner'S Manual

Search results

Summary of Contents for BULL 200s

Reviews:

Related manuals for BULL 200s

Brands by name

Popular brands