Tao Motor BULL 200s Owner'S Manual Download Page 19 | Manualshive

Page: 19 / 79

background image

Fuel OFF

Fuel ON

FUEL COCK/ FUEL VALVE

FUEL COCK/ FUEL VALVE
The fuel cock/valve supplies fuel from the tank to the carburetor.

The fuel cock/valve lever positions are explained as follows and shown in the illustrations.
FUEL OFF

Arrow mark positioned over

“OFF”

position. Fuel is off and fuel will not flow to the carburetor. Always turn the fuel valve to the

"

OFF" position and allow the engine to idle until it burns remaining fuel in the line when the ATV is being stored. Once the fuel

in the line has been cleared, drain the carburetor bowls. Following this procedure will help reduce corrosion and carburetor

damage.
FUEL ON

Arrow mark positioned over

“ON” position. Fuel is on and fuel will flow to the carburetor.

STORAGE

Drain gasoline from the fuel tank and carburetor of the ATV if being stored for more than over 48hrs.

10

«
...
17
18
19
20
21
...
»

Summary of Contents for BULL 200s
















































































Reviews:

No comments

Related manuals for BULL 200s

Brand: Yamaha Pages: 200

Brand: Yamaha Pages: 218

YXZ 1000R SS 2020

Brand: Yamaha Pages: 220

Brand: Yamaha Pages: 126

Formula Mx 1988

Brand: BOMBARDIER Pages: 62

traxter max series

Brand: BOMBARDIER Pages: 174

outlander max 800

Brand: BOMBARDIER Pages: 160

Brand: BOMBARDIER Pages: 282

Tugger train Autarkic E Frame

Brand: Still Pages: 144

Brand: Texas Pages: 7

Brand: IBOTECH Pages: 60

2014 SNO PRO 500

Brand: Arctic Cat Pages: 90

Brand: Arctic Cat Pages: 68

Brand: Arctic Cat Pages: 80

Brand: Arctic Cat Pages: 76

2010 1000 H2 TRV

Brand: Arctic Cat Pages: 104

Brand: SILLA Pages: 52

Brand: Costway Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands