background image

 

 

VOIP-600

 

Series Phone 

Configuration / Operation Manual

 

 

Page 

61

 of 

94

 

 

 

Rev. 9/17/2014

 

 

Copyright 2014 Talk-A-Phone Co.

 • 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • info@talkaphone.com • www.talkaphone.com.  

All prices and specifications are subject to change without notice. Talk-A-Phone, Scream Alert, WEBS and WEBS Contact are registered trademarks of Talk-A-Phone Co. All rights reserved.

 

5.  Operations 

The phone takes approximately one minute to boot. While the first and second LED’s are flash, the unit is still 

booting (Refer to Figure 1 Front View). After all LED’s clear, wait for an additional twenty seconds before 

initiating a call. 

The phone needs to be programmed in accordance with the instructions provided in Chapter 4 (Refer to 4 

Using the Web GUI). 

5.1.  Calling Emergency/Information Numbers 

In case of an emergency, the phone can dial a list of numbers (Refer to 4.5.1 Number Lists) in round robin 

fashion. Depending on the device mode and programming, a call is automatically initiated when: 

 

Push button is pressed

 

 

 

Auxiliary Input is activated

 

 

 

Handset goes off-hook (0BH device mode only) 

If the first number does not answer within a specified time (Refer to 4.5.4 Call Parameters) the phone dials 

the next number from the number list. It continues to dial in round robin fashion until the call is answered, or 

the call conversation timer expires (Refer to 4.5.4 Call Parameters: Call Conversation Timer). 

5.2.  Answering the Emergency/Information Call 

One of the following scenarios occurs upon answering the emergency call on the remote side: 

 

The VOIP-600 Series Phone may transmit its location by playing a recorded message (Refer to 4.7.2 

Played to Remote Side). If no such feature is enabled or when the voice message completes playing, 

the caller may talk and listen hands-free

19

 without using any controls. 

 

The VOIP-600 Series Phone may transmit a voice message and request that the remote side user to 

press a specific key on the keypad of the remote side phone (Refer to 4.5.4 Call Parameters: answer 

a call) to answer this call. Providing the incorrect key sequence within three attempts will terminate 

the call. Once the call is terminated, a new call is made to the next number on the list. On providing 

the correct key sequence, the VOIP-600 Series Phone may transmit its location by playing a recorded 

message (Refer to 4.7.2 Played to Remote Side). If no such feature is enabled, the caller may talk 

and listen hands-free

20

 without using any controls. 

5.3.  Terminating Calls 

Round robin calls can be terminated only from the remote side by going on-hook or by pressing a specific call 

termination key on the remote keypad (Refer to 4.5.4 Call Parameters). Calls placed from the keypad can be 

terminated locally using button(s) programmed as a hook switch (Refer to 4.6.1 Buttons) or from the remote 

side by going on-hook/pressing a specific call termination key.  

For phones with just a handset and no speaker, calls (both round robin and keypad calls) can be terminated 

locally by going on-hook. 

 

                                      

19

 Depends on device mode 

20

 Depends on device mode 

Summary of Contents for VOIP-600 Series































































































Reviews: