background image

 

Area of Rescue Command Unit

 

Installation Guide 

Model AOR-5 / Model AOR-10

 

Page 

1

 of 

23

 

 

  Rev. 4/13/2022

 

 

Copyright 2022 Talk-A-Phone, LLC

 

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • [email protected] • www.talkaphone.com.  

 

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, bAlert, Scream Alert, WEBS, and WEBS Contact are registered trademarks of 
Talk-A-Phone, LLC.  All rights reserved.  All other trademarks mentioned in this document or website are the property of their respective owners and does not imply or indicate 
any approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated. 

I. 

Introduction 

This installation guide provides instructions for installation, programming, and operation of 

Model 

AOR-5 or Model AOR-10

.  For instructions on installation or programming of Talkaphone Area of 

Rescue Call Stations, please refer to the manual for the AOR-CSE Analog Call Station. 

It is recommended that this instruction set be read completely prior to the start of any installation. 

II. 

Contents 

Please ensure receipt of each of the included 

AOR-5 / AOR-10 

components: 

QTY 

Part Number 

Description 

AOR-5 or AOR-10 

5- or 10-Station Area of Rescue Command Unit 

68684 

12VDC, 4.5Ah Backup Battery 

Optional components (sold separately) include: 

QTY 

Part Number 

Description 

AOR-TR10 

Trim Ring for Flush Mounting Model AOR-5 or Model 
AOR-10 

without

 Latched Door 

AOR-TR10-D 

Trim Ring for Flush Mounting Model AOR-5 or Model 
AOR-10 

with

 Latched Door 

42970 

6-18 Phillips Screw for Flush Mount Trim Ring 

 

 

 

THIS  PRODUCT  MUST  BE  INSTALLED  IN  ACCORDANCE  WITH  THE 
APPLICABLE  INSTALLATION  CODE  BY  A  PERSON  FAMILIAR  WITH 
THE  CONSTRUCTION  AND  OPERATION  OF  THE  PRODUCT  AND  THE 
HAZARDS INVOLVED  

CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION 
PERTINENT,  PAR  UNE  PERSONNE  QUI  CONNAÎT  BIEN  LES  PRODUIT 
ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS

 

Summary of Contents for AOR-5
























Reviews: