background image

 

Area of Rescue Command Unit

 

Installation Guide 

Model AOR-5 / Model AOR-10

 

Page 

15

 of 

23

 

 

  Rev. 4/13/2022

 

 

Copyright 2022 Talk-A-Phone, LLC

 

• 7530 North Natchez Avenue • Niles, Illinois 60714 • Phone 773.539.1100 • info@talkaphone.com • www.talkaphone.com.  

 

All prices and specifications are subject to change without notice. Talk-A-Phone, Talkaphone, bAlert, Scream Alert, WEBS, and WEBS Contact are registered trademarks of 
Talk-A-Phone, LLC.  All rights reserved.  All other trademarks mentioned in this document or website are the property of their respective owners and does not imply or indicate 
any approval, endorsement, sponsorship, or affiliation with such owners unless such approval, endorsement, sponsorship, or affiliation is expressly indicated. 

6. 

Recording a Location Message: 

a.  Record the location message for the AOR-CSE Station in question:  

* 4

 

Wait for the tone to begin speaking/recording.  The recorded message has a maximum 
length of 

16 seconds

b.  Press any key to stop recording or it will end after 16 seconds.  The recorded message 

will automatically play back. 

c.  To review the recorded message again, press:  

* 5

 

d.  To delete the recorded message, press:  

* 3

 

7. 

To exit programming and disconnect, press:  

# 7

 

 

Summary of Contents for AOR-5
























Reviews: