background image

5

3

2

1

4

5

3

13

<Left side>

Temporarily attach the 2 truss-head screws.

Slide the reclining pedal in.

Fix using the third truss-head screw.

Firmly tighten the temporarily attached screws.

2

3

<Right side>

Swap the reclining pedal and the base cover attachment fitting from left to right.

Remove the reclining pedal and the base cover 

attachment.

Reclining pedal

Truss-head screws M5 x 12 (Black) , 3screws

Base cover attachment

Hexagonal head bolt M5 x 14 , 3screws

Base cover

Truss-head screws M4 x 10 (Black) , 6screws

Remove the maintenance cover and the base cover.

Maintenance cover

Base cover

Check that pressing the reclining pedal 
with your foot reclines the backrest, and 
lifting your foot off the reclining pedal 
fixes the backrest in place.

Attach the base cover and maintenance 

cover.

×3

×3

×3

×3

-3

3

-1

3

-4

3

-2

3

-1

3
3
3

-4

-3

-2

Procedure for swapping the reclining pedal from left to right.

This product has a reclining pedal on its left side.
Depending on the salon layout, if it is necessary to install the reclining pedal on the
right side, then swap the position of the reclining pedal from left to right in accordance 
with this manual.

Reclining pedal

Reclining pedal

Base cover attachment

Summary of Contents for YUME NAGOMI





















Reviews: