background image

 

 

y

  Engine start control switch 

The switch button position is under seat. 

ON

 position: Engine is locked and can not be started engine in this 

position. 

 

OFF

 position: When the ignition switch is 

on

 position, the start 

control switch is 

off

 position, press electrical starter 

button while holding the front or rear brake lever will 
start the engine. 

 

y

 

Horn Switch 

  Press this button down when ignition switch is in the 

ON

 position, the horn will sound. 

y

 

Turn Signal Switch 

Turn signal lights are used when turning left/right or changing lane. 
Turn ignition switch to the 

ON

 position, and slide the turn signal switch to left or right . Then, the turn 

signal lights will flash. 
To release, simply return the turn signal light button to the original position. 

      Right-side turn signal light flashing means you intend to make a right turn. 

       Left-side turn signal light flashing means you intend to make a left turn. 

 

 

§

STORAGE BOX

§

 

y

  This box is located under the seat. 

y

 Maximum 

load 

capacity:5kg.

 

y

  Do not store valuables in the box. 

y

  Make sure that the seat has been locked completely after it was 

pressed down. 

y

  Take out valuables before washing to avoid wetting these objects. 

y

  Do not place thermal sensitive objects in the box because of 

engine’s heat and high temperature.

 

 

 

 

 

Storage box

Engine start 

control switch

Summary of Contents for JE05W1-6
























Reviews: